background image

 

Tavor 8-Sub - Installing the Tavor 8-Sub 

 

Installing the Tavor 8-Sub 

This section explains how to: 

 

Choose the best location (see 

Section 

 5.1

 

Install the wires (see 

Section 

 5.2

Section 

 5.3

 describes the different subwoofer setups. 

5.1 

Choosing the Best Location 

Position your subwoofer on a hard surface or hang it on the wall: 

 

Keep the vibrations to a minimum 

 

Do not cover or place anything on the 

Tavor 8-Sub

 

Before installing the subwoofer: 

 

Experiment by placing the subwoofer in different locations and check the 

sound before finally deciding on the most suitable location (see installation 

instructions in 

Section 

 5.2

) where the subwoofer sound blends smoothly with 

the speakers.  

Note that the ideal place would be between the two front speakers, but other 

locations may produce good results. 

 

Do not place the subwoofer directly in the central dividing line of the room, it 

should be located toward the left or the right of the central dividing line 

5.2 

Installing the Tavor 8-Sub

 

To install the 

Tavor 8-Sub

:

 

1.  Connect 

one

 of the optional inputs to a receiver or to an active speaker (see 

Section 

 5.3

2.  Connect the power. 

3.  Press the ON switch. 

Summary of Contents for Tavor 8-Sub























Reviews: