Kramer SPK-I651T-KI User Manual Download Page 16

Page: 16 / 18

Yarden 6-ID - Technical Specifications

Technical Specifications

Audio and Power

DESCRIPTION:

2-way in-wall speaker

FREQUENCY RESPONSE:

40Hz to 20kHz @ -10dB
60Hz to 20kHz @ ±3dB

WOOFER:

6.5

” (166mm) Kevlar(R) with rubber surround

TWEETER:

2 pivoting 1

” (25mm) titanium

IMPEDANCE:



(transformer tap in off position)

TRANSFORMER TAPS:

70V

– 30W / 15W / 7.5W / 3.7W / Off (Lo-Z)

100V

– 30W / 15W / 7.5W / Off (Lo-Z)

SENSITIVITY:

85dB SPL, 1W@1m

MAX SPL:

Continuous: 100dB
Peak: 103dB

POWER HANDLING

30W RMS
80W continuous program

CROSSOVER FREQUENCY:

2.3kHz

DIRECTIVITY FACTOR (Q):

7.5, averaged 1kHz to 10kHz

DIRECTIVITY INDEX (DI)

8.8dB averaged 1kHz to 10kHz

INPUT CONNECTORS:

Terminal blocks

CONTROLS:

Mono/Stereo select switch, Music/Speech select
switch

Shipping and Installation

MATERIALS:

Frame, aluminum grill, ABS cabinet

OPERATING TEMPERATURE:

0° to +40°C (32° to 104°F)

STORAGE TEMPERATURE:

-40° to +70°C (-40° to 158°F)

HUMIDITY:

10% to 90%, RHL non-condensing

WEIGHT:

3.03kg (6.68lbs) approx.

SHIPPING WEIGHT:

3.85kg (8.49lbs) approx.

DIMENSIONS:

48cm x 28cm x 8.8cm (18.9

” x 11.02” x 3.46”), W, D, H

INSTALLATION CLEARANCE:

mounting depth: 8.3cm (3.27")

COLORS:

Available in white

Specifications are within a 10% tolerance and are subject to change without notice at

http://www.kramerelectronics.com

Summary of Contents for SPK-I651T-KI



















Search results

Summary of Contents for SPK-I651T-KI

Reviews:

Related manuals for SPK-I651T-KI

Brands by name

Popular brands

Kramer SPK-I651T-KI, User Manual

Search results

Summary of Contents for SPK-I651T-KI

Reviews:

Related manuals for SPK-I651T-KI

Brands by name

Popular brands