background image

 

Galil 4-C Installing the Galil 4-C 

 

 

Figure 4: Mounting the Galil 4-C Closed-back Ceiling Speaker 

2.  Place the tile rails on the tile and snap them into the two tabs on the C-ring. 

Align the rails so that the ends extend over the T-channel grid. 

3.  Insert a screw through each tab on the C-ring to secure the rails. 

4.  Connect the speaker wires to the appropriate connector terminals: 

 

PIN 1 and PIN 2 are connected internally and are positive (+) 

 

PIN 3 and PIN 4 are connected internally and are negative (-) 

Screw the hold-down screws on the connector until tight, using a small 

screwdriver. 

You can connect the speakers in the two following possible layouts: 

 

Wiring in parallel

: connect the amplifier directly to each of the 

speakers. When one input connector is removed, subsequent 

speakers will remain connected (see 

Figure 3

 

Daisy-chaining

: connect the wire pair (+ and -) of the speaker to the 

subsequent s and -. When one input connector is removed, 

subsequent speakers will be disconnected (see 

Figure 3

5.  Plug the connector into the socket (see 

Figure 5

). 

6.  Run the wires through the opening in the input terminal cover and then 

connect to the speaker terminal block connector. 

T-channel Grid

Support Ring
Screws

Ceiling Tile

Tile Rails

C-ring

Summary of Contents for Galil 4-C





















Reviews: