background image

 

RC-76R/RC-78R - Overview 

 

Overview 

The 

RC-76R/RC-78R

 is a 6-button/8-button control keypad that fits into standard 

1 gang US wall junction boxes. Connected over Ethernet to Site

-

CTRL™ remote 

AV control, site management & monitoring system, as well as LAN-connected 
control gateways for extended controlled devices capacity, and over KNET™ to 
master room controller and auxiliary keypads for remote keypad control, it can 
flexibly serve either as a standalone room controller, part of a multi-unit KNET™ 
system, or part of a multi-unit Ethernet system managed by the Kramer Site

-

CTRL™ site management platform. The 

RC-76R/RC-78R

 have identical 

functionality.  

The 

RC-76R/RC-78R 

 features: 

 

6/8 configurable, RGB backlit, front panel buttons, configured using the 

K-Config

 configuration software 

 

1 general purpose I/O port that can be configured by 

K-Config

 as a digital 

input, digital output or analog input for interfacing with a variety of devices 
such as sensors, switches, LEDs, or relays 

 

2 bidirectional RS-232 ports that can control AV equipment such as 
projectors, LCD and PDP displays, power amplifiers, switchers and scalers 

 

2 relay contact closure ports that can control other room items related to the 
AV system, such as, raising and lowering drapes, a screen or a projector 

 

2 IR control ports with an IR learning receiver behind the design frame that 
learns commands from any IR remote 

 

1 RS-485 control port 

 

Compatibility with Kramer 

Site-CTRL

 software for network remote control 

and management over the Ethernet port 

 

K-NET

™ control channel that connects compatible user interfaces, supply 

power and control data over a single cable 

 

Flexible control via Ethernet and 

K-NET

  

 

Standard 1 gang US junction box size 

Summary of Contents for 2900-300253

























Reviews: