manualshive.com logo in svg

KRAL BEM 300 Series, Operating Instructions Manual

Share
Download
KRAL BEM 300 Series Operating Instructions Manual Download Page 26

26

OIE 15en  Edition 2019-12 HW 2.0/SW 2.0 

Operating Instructions

Operation at a glance

Operation of the basic functions

Operating the basic functions

The following table describes the basic operating steps. They can be carried out in part without a pass-
word having to be entered.

Tab. 3 Operating the basic functions

Aim

Operating steps

Reading the consumption

see "1.01 Volumeter A", page 29

► Press the ARROW UP and ARROW DOWN keys simul-

taneously.
"Volumeter A" is displayed.

Resetting totals

see "1.02 Volumeter A Total with reset-
ting", page 29

1. Select Menu 1.02.
2. Press SET.

Total 1 flashes.

3. Press SET for 3 seconds.

Total 1 is set to 0.

4. Press SET.

Total 2 flashes.

5. Press SET for 3 seconds.

The password prompt is displayed.

6. Enter the password.

Total 2 is reset.

Select the language

see "1.07 Language selection", 
page 29

1. Press SET and ARROW RIGHT simultaneously.

"Language selection" is displayed.

2. Press SET.
3. Press ARROW DOWN / ARROW UP to select the langu-

age.

4. Press SET.

The language is selected.
After you have navigated to a different page, the lan-
guage is used in the display.

Calling up help

see "1.12 Help operation", page 29

1. Press the ARROW RIGHT and ARROW LEFT keys 

simultaneously.
Information about the operation is displayed.

2. Scroll using ARROW UP / ARROW DOWN.
3. Use SET to exit the page.

Summary of Contents for BEM 300 Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands