manualshive.com logo in svg

KRAL BEM 300 Series, Operating Instructions Manual

Share
Download
KRAL BEM 300 Series Operating Instructions Manual Download Page 29

Operating Instructions

OIE 15en  Edition 2019-12 HW 2.0/SW 2.0 

29

Start

Menu description

Start

After the power supply has been switched on, a 
start message indicates that the electronic unit is 
ready to operate. The display of the start mes-
sage can be activated or deactivated, see "2.09 
Start message", page 32.

Start message

If the display of the start message is activated, it 
is displayed for three seconds. This is followed 
directly by the "Volumeter A" page.

Shortcut pages

The following pages can be called up from the 
various windows as required by means of key 
combinations, see "Key assignment", page 24.

1.07 Language selection

Shortcut: Press SET and ARROW  RIGHT 
simultaneously.

1. Press SET.
2. Use ARROW UP or ARROW DOWN to select 

the desired language.

3. Press SET.

The selected language is applied after a diffe-
rent page has been called up.

1.12 Help operation

Shortcut: Press ARROW LEFT and ARROW 
RIGHT simultaneously.

This page displays brief instructions for opera-
ting. Press ARROW UP or ARROW DOWN to 
navigate in the text. Use SET to exit the help.

Menu 7: Alarms

Shortcut: Press SET and ARROW LEFT 
simultaneously.

Use ARROW UP and ARROW DOWN to call up 
the existing alarms.

Menu 1: Display

Menu 1 "Display" displays the measured values. 
Totals can be reset here; the contract and backg-
round illumination of the display can be set.

1.01 Volumeter A

The flow rate in Volumeter A is displayed on the 
"Volumeter A" page.

1.02 Volumeter A Total with resetting

The "Total" page displays the total consumption 
value since the last resetting. 

Note: 

Depending on the number of decimal pla-

ces the total value stops at the following mini-
mum or maximum values:  .

Summary of Contents for BEM 300 Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands