KRain KRX8 User Manual Download Page 39

39 of 40

39 of 40

Warranty

5 Year Replacement Guarantee

Holman Industries offers a 5 year 
replacement guarantee with this product.

In Australia our goods come with guarantees 
that cannot be excluded under the Australian 
Consumer Law. You are entitled to a 
replacement or refund for a major failure 
and compensation for any other reasonably 
foreseeable loss or damage. You are also 
entitled to have the goods repaired or replaced 
if the goods fail to be of acceptable quality and 
the failure does not amount to a major failure.

As well as your statutory rights referred to 
above and any other rights and remedies 
you have under any other laws relating 
to your Holman product, we also provide 
you with a Holman guarantee.

Holman Industries guarantees this product 
against defects caused by faulty workmanship 
and materials for 5 years domestic use from 
the date of purchase. During this guarantee 
period Holman Industries will replace any 
defective product. Packaging and instructions 
may not be replaced unless faulty.

In the event of a product being replaced during 
the guarantee period, the guarantee on the 
replacement product will expire 5 years from 
the purchase date of the original product, 
not 5 years from the date of replacement.

To the extent permitted by law, this Holman 
Replacement Guarantee excludes liability 
for consequential loss or any other loss or 
damage caused to property of persons arising 
from any cause whatsoever. It also excludes 
defects caused by the product not being used 
in accordance with instructions, accidental 
damage, misuse, or being tampered with 
by unauthorised persons, excludes normal 
wear and tear and does not cover the cost of 
claiming under the warranty or transporting 
the goods to and from the place of purchase. 

Should you suspect your product may 
be defective and need some clarification 
or advice please contact us directly:

1300 716 188 

[email protected] 

11 Walters Drive, Osborne Park 6017 WA

If you are certain your product is defective and 
is covered by the terms of this warranty, you will 
need to present your defective product and your 
purchase receipt as proof of purchase to the 
place you purchased it from, where the retailer 
will replace the product for you on our behalf.

Summary of Contents for KRX8









































Reviews: