Instruction Manual
Electric Tile Cutter
www.kraftool.hk
www.kraftool.hk
|
|
7
6
Preparation for work
The
product has a standard
cutting
disc. If it is
necessary to install a
nother
disk
,
corresponding to
the upcoming work, replace the disk according to
the Assembly section.
Prepare yourself for work:
`
prepare and put on protective equipment
(glasses, headphones);
`
prepare the workpiece to be processed and
make sure that its thickness matches the
maximum allowed for your
tile cutter;
`
make sure the drive is securely attached to
shaft and not locked; To do this, push the disc with
your hand in the direction of rotation. With free
rotation, there should be no extraneous sounds. If,
when the disc rotates, extraneous noise is heard,
tighten the disc mount or replace the disc;
`
remove
wrenches
and other objects from
rotating parts of the product.
Fill the
tray
13
with water to the level between the
risks on the lower protective c
over
8
.
18
7
3
The product is intended only for wet cutting.
Always fill the tray with water before use and
periodically check its level during operation.
If necessary, adjust the cutting width:
`
loosen the thumbscrews at both ends of
the guide fence 7
;
`
adjust the required cutting width on the
scale on the desktop;
`
Tighten the fixing screws.
Note!
The longitudinal stop can be installed both
on the right and on the left side of the disk.
18
11
12
2
If necessary, adjust the angle of the cut:
`
loosen the thumb screws
12
fixing the
angle of the table (on both sides);
`
adjust the required table angle on a
tilt
scale
11
;
`
tighten the screws
12
.
If
a slanting cutting at an angle of 45° is
necessary,
set on the longitudinal stop
7
angular
stop
3
.
Operating procedure
Connect the product to the mains.
The product corresponds to class I protection
against electric shock, i.e. must be grounded
(for this, grounding contacts are provided in
the plug). Do not alter the plug if it does not fit
your outlet. Instead, a qualified electrician
should install the appropriate outlet.
The inclusion of the product is carried out by
pressing the “I” button of the switch 1.
Note!
Electromagnetic product switch. If the mains
voltage fails and its subsequent appearance, the
product will not turn on independently. To turn on
the product in this case, press the "I" button again.
Note!
Start work only after the disc picks up the
pace.
Place the workpiece on the
work table
, press it
against the edge of the guide
7
or put it in the
corner stop
3
.
If it is necessary to cut large-sized workpieces,
you can increase (only for EP-200-1000N) the
width of the table by extending the table
9
. To do
this, loosen the screws
10
for fixing the extension
and slide it to the required distance. After installing
in a suitable position, tighten the screws
10
.
For cutting, use the workpiece sliding on the table.
During work, always STRONGLY hold the
workpiece.
When working with the product, monitor the
engine speed. A drop in speed of 20% or more
indicates an overload. In this case, it is necessary
to reduce the
push
force
to
the disc.
Note!
On the tile cutter model EP-200 1000N
installed thermal fuse,
it will
automatically
disable
the engine when it is overloaded or overheated.
To resume power supply, allow the engine to cool
down and restore the fuse by pressing button
19
.
To resume operation, turn on the product using
the switch.
When working with the product, watch the water
level in the
tray
and
fill it up
as needed.
At the end of the work, turn off the product by
pressing the “0” button of the switch.
Then unplug
the product from the
mains
.
The disc heats up during operation. Do not
touch it immediately after work is completed
and until it is completely cooled.
Carefully remove all debris from the
work table
and from under the protective cover.
To avoid injury or damage, do not remove
debris
by hand. Use a brush.
Periodic maintenance
Conduct a
ll work on the assembly,
replacement and adjustment of produce only
when
the product is disconnected from mains
.
During the operation periodically required:
а)
a
replacement of water and cleaning of the
tray
from the accumulated products of the cut;
б)
a
replacement (as wear)
of
cutting disc. To do
this, follow the steps in
s
ection Assembly.
Recommended
practices
Before starting work, make sure that there is no
visible mechanical damage to the product and the
disk. A disk with cracks, chips and other damage
must be replaced immediately.
To avoid injury to the operator and damage to
the product DO NOT use the product with a
damaged disc.
Make sure that your mains voltage matches the
rated voltage of the product.
Connect the product to the mains only when you
are ready to work.
Before using the product for the first time, turn it
on without load and let it work for 20-30 seconds If
at this time you hear extraneous noise, feel
increased vibration or the smell of burning, turn off
the product, disconnect the power cable from the
mains and determine the cause of this
phenomenon. Do not turn on the product before
the cause of the malfunction has been found and
corrected.
Ensure good lighting and order in the workplace -
inadequate lighting and foreign objects can cause
damage and injury.
ATTENTION
`
take measures to prevent sagging (causes
uneven breaking off or injury when falling) of
the notched workpiece;
ATTENTION
ATTENTION
ATTENTION
ATTENTION
ATTENTION
ATTENTION
