background image

5 | 

P a g e

 

 

 



Always wear a dust mask when cleaning the system and when removing ashes to avoid damages to 

your health.  



When setting the domestic water temperature above 60 °C, you have to ensure that the hot water is 

mixed with cold water to avoid scald.  



The pellet heater system may only be set up and operated in heating and plant rooms which 

comply with legal requirements.  



Provide an appropriate air relief valve on top of the boiler.  



Annual control of safety devices by a specialist.  



Regular control of expansion tank by a specialist.  



Regular control of pellet feeding devices, automatic ignition devices and feeding features.  



Please note that even when the system is turned off, different functions are in operation. 

(For 

example the anti-freeze protective device; pumps and mixers are moved periodically during the night 
avoid an accumulation of the storings). 

To ensure that no electricity runs through the system, take 

off the system from electricity. 

 



Make sure that the return temperature does not drop below 50 °C. Disregarding leads to expiry of 

warranty!  

 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for Propel 25


























Reviews: