“S” type speed sensor bracket
Overview
Function Specifications
Button function
Stand by function instruction
NOTE
●
P.S.
2-3
3-1
3-2
3-3
3-4
Put the magnet into the
brake disc screw hole.
Ex 1: If the disk brake has
3 screws
,
you can install
1 or 3 magnets
.
Ex 2: If the disk brake has 4 screws,
you can install 1,2 or 3 magnets.
Ex 3: If the disk brake has 5 screws,
you can install 1 or 5 magnets.
Ex 4: If the disk brake has 6 screws,
you can install 1,2,3 or 6 magnets.
Install the S type sensor
bracket.
Adjust the sensor bracket
position to make sure the
sensor is facing the magnet
to receive good speed signal.
Install the speed sensor
on the bracket.
In order to get a good speed
signal, the distance between
the speed sensor and magnet
should be under 5 mm.
Fuel Level
●
Display range: 4 segment
●
The fuel segment will flash when
only 1 level left.
●
If you don’t install the fuel
wire, the fuel will not display.
Indicators
lights
●
Turn signal (Green)
●
Neutral (Green)
●
High beam (Blue)
●
Engine oil pressure (Red)
●
EOBD (Amber)
EX. 1 EX.2
EX. 3 EX.4
Odometer
●
Display range: 0~99999.9 km (mile),
automatic reset after 99999.9 km(mile).
●
Display unit: 0.1 km(mile).
Trip meter A. B
●
Display range: 0~999.9 km (mile),
automatic reset after 999.9 km(mile).
●
Display unit: 0.1 km(mile).
Fuel / Remaining Distance
●
Display range: 999.9~0 km (mile).
Design and specification are subject to change without notice!
Press the Select button
• In main screen: press the
Select button
to switch between clock, volt.
• In setting screen: press the
Select button
to change the setting cursor.
• When the meter is off, press the
Select button
to wake up the clock.
Press the Adjust button
• In main screen: Press the
Adjust button
to switch between Odometer, Trip A, Trip B,
Fuel / Remaining distance.
• In setting screen: Press the
Adjust button
to change the setting value.
• When the meter is off, press the
Adjust button
to wake up the clock.
Press and hold the Select button for 3 seconds.
• In main screen: press and hold the
Select button for 3 seconds
to switch
between fuel, volt, RPM.
• In setting screen: press and hold the
Select button for 3 seconds
to return the
main screen
Press and hold the Adjust button for 3 seconds
• In record screen such as Trip A, Trip B ,press and hold the
Adjust button for 3 seconds
to reset the record, and switching the unit for Mileage and Speed.
.
Press and hold the Adjust button for 10 seconds
• In Fuel / Remaining distance screen: Reset the Remaining Mileage to 0 and restart
the learning.
.
Press and hold the Adjust button
• In setting screen: To switch the setting value faster by holding pressing the
Adjust button.
Press and hold the Select buttons for 3 seconds
• In main screen, press and hold the Select buttons for 3 seconds to enter the
setting screen.
●
When the meter is off, press
Adjust or Select
button
to wake up the clock function.
●
The clock will be displayed 30 sec. after
waking up.
Clock
●
24 H.
Digital Volt meter
●
Display range: DC 5~24 V.
Speedometer
●
Display range: 0~360 km/h.
(0~225 MPH)
●
Display unit: 1 km/h (MPH)
Volt meter
●
Display range: 4 levels.
●
The voltage segment will
flash when only 1 level left.
Tachometer
●
Display range: 15 levels.
●
Each level represents 1000
RPM.
Higher number of magnets installed on the disk brake
will result in a faster speed display on the gauge.
The letter “N” on the magnets must face the speed
sensor in order to pick up correctly the speed.
Display range: DC 5 ~ 24 V
Will flash when <8V or >18V
•
Digital Volt meter
•
Speedometer
Display range: 0 ~ 360 km/h (0 ~ 225 MPH)
Display unit: 1 km/h or MPH for alternative
Display range: 0 ~ 999.9 km (mile),
automatic reset after 999.9 km (mile)
Display unit: 0.1 km (mile)
•
Trip meter A / B
Setting range: 300 ~ 2500 mm
Setting unit: 1mm / Sensor point 1 ~ 20
•
Tire circumference
Display range: 4 segments
Low fuel symbol flashing when 1 segment left.
•
Fuel level
•
Display internal
•
Odometer
Display range: 0 ~ 99,999 km (mile),
automatic reset after 99,999 km (mile)
Setting unit: 1 km (mile)
<0.5 second
•
Fuel / Remaining
distance
•
Clock
12 / 24 H
•
Volt meter
Display range: 4 segments
Dispaly unit: 1 segment (Low) - DC 11.6~12.0 V
2
segment- DC 12.1~12.5 V
3
segment - DC 12.6~13.0 V
4
segment (High) - DC 13.1 V
•
Low voltage warning
Voltage segments will flash when only
1 segment is left.
•
Backlight brightness
Setting range: 1-5(Darkest)~5-5(Brightest)
Setting unit: 20 % each segments
DC 12 V
•
Effective voltage
•
Effective temperature range
135.7 X 100.7 X 52 mm
Turn signal(Green) / Neutral (Green)
Oil Light (Red) / EOBD (Amber) / High beam (Blue)
-10 ~ +60 °C
•
Meter standard
•
Meter size
JIS D 0203 S2
Around 240 g
•
Meter weight
•
Indicator light color
Display range: 999.9 ~ 0 km (mile)
Display unit: 0.1 km (mile)
Setting range: 100
Ω
- 250
Ω -
510
Ω -
1200
Ω
•
Fuel resistance
Display range: 15 segments
Display unit: 1 segment = 1000 RPM
•
Tachometer
