Ef
fect
151
Filter and dynamics control effects
000: No Effect
Select this option when you do not wish to use any effects.
The Insert Effect section outputs unprocessed signals and the
Master Effect section mutes the output.
001: St.Amp Sim
(Stereo Amp Simulation)
This effect simulates the frequency response characteristics of
guitar amplifiers. It is also effective for organ and drum
sounds.
002: St.Compressor
(Stereo Compressor)
This effect compresses the input signal to regulate the level
and give a “punchy” effect. It is useful for guitar, piano, and
drum sounds. This is a stereo compressor. You can link left
and right channels, or use each channel separately.
a: Envelope
This parameter selects whether the left and right channels are
linked to control both signals simultaneously, or whether each
channel is controlled independently.
b: Sensitivity, d: Level
The “Sensitivity” parameter sets the sensitivity of the compressor.
If this parameter is set to a higher value, lower level sounds will
be boosted. With a higher Sensitivity, the overall volume level is
higher. To adjust the final volume level, use the “Level” parame-
ter.
c: Attack
This parameter controls the attack level.
003: St.Limiter
(Stereo Limiter)
The Limiter regulates the input signal level. It is similar to the
Compressor, except that the Limiter compresses only signals
that exceed the specified level to lower unnecessary peak sig-
nals. The Limiter applies a peaking-type EQ to the trigger sig-
nal (which controls the degree of the Limiter effect), allowing
you to set any band width to be covered. This effect is a stereo
limiter. You can link left and right channels, or use each chan-
nel individually.
Filter/Dynamic
a
Amplifier Type
Selects the type of guitar amplifier
SS, EL84, 6L6
b
W/D (Wet/Dry)
Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source)
Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
–100...+100
a
Envelope (Envelope Select)
L/R Mix, L/R Individually
Determines whether the left and right channels are linked or used
separately
☞
b
Sensitivity
Sets the sensitivity
1...100
☞
c
Attack
Sets the attack level
1...100
☞
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Amp Simulation Filter
Amp Simulation Filter
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
EQ Trim
EQ Trim
LEQ
HEQ
LEQ
HEQ
Compressor
Compressor
Envelope Select
Output Level
Output Level
Envelope - Control
Envelope - Control
d
Level (Output Level)
Sets the output level of the compressor
0...100
☞
,
(Source)
Off...Tempo
Selects the modulation source for the compressor output level
(Amount)
–100...+100
Sets the modulation amount of the compressor output level
e
Pre EQ Trim
Sets the EQ input level
0...100
f
LoEQ (Pre Low EQ Gain)
Sets the gain of Low EQ
–15.0...+15.0dB
HiEQ (Pre High EQ Gain)
Sets the gain of High EQ
–15.0...+15.0dB
g
W/D (Wet/Dly)
Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source)
Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
–100...+100
Sensitivity=100
Sensitivity=40
Dry
Wet
Time
Level
Compressor - Sensitivity
Louder
Dry
Wet
Time
Level
Attack=80
Attack=20
Compressor - Attack
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Limiter
Limiter
Envelope Select
Gain Adjust
Gain Adjust
Side PEQ
Envelope - Control
Envelope - Control
Trigger Monitor
+