Korg NAUTILUS Series, Parameter Manual, Page: 537 / 961

SEQUENCER: Page Menu Commands Auto HDR/Sampling Setup
527
Auto HDR/Sampling Setup
This command walks you through making the appropriate
settings for various common operations, including drive
recording, audio track bouncing, and sampling/resampling
(in-track sampling, etc.). For more information, see “Auto
HDR/Sampling Setup” on page 527 of the Parameter Guide.
When you execute this operation, the relevant parameters
will be set automatically. You cannot use the page menu
command “Compare” to revert to the prior settings.
The settings are automatically made for the most typical
applications. After executing the auto setup operation,
you can further adjust any of the parameters as described
in the paragraphs for each item.
1. Select Auto HDR/Sampling Setup to open the dialog
box.
2. Use the radio buttons to select the type of settings you
want to make.
Initialize:
Set parameters related to drive recording and
sampling to their default values.
HDR (Audio Track Recording): Makes the necessary
settings for recording external audio signals such as
guitar or vocal from the audio inputs to audio tracks.
Bounce Audio Track: Makes the necessary settings for
bounce-recording audio tracks.
2ch Mix to Disk: Makes settings for resampling a
completed song in order to create a two-channel stereo
WAVE file on the drive.
Resample SEQ Play: Makes settings so that you can
resample your keyboard playing in SEQUENCER mode.
In-Track Sampling: Makes settings to sample only an
external audio signal using the In-Track Sampling
function.
3. The settings for the rest of the procedure will depend
on what you selected in step 2. (For details, refer to the
explanations below.)
Initialize
1. Refer to Auto HDR/Sampling Setup steps 1 and 2, and
select Initialize.
2. Press the OK button to execute the command. If you
decide not to execute, press the Cancel button.
For more information, see “Auto HDR/Sampling Setup:
Automatically-set parameters and their values” on
page 531.
HDR (Audio Track Recording)
1. Refer to Auto HDR/Sampling Setup steps 1 and 2, and
select HDR (Audio Track Recording).
2. Press the OK button to open the dialog box.
3. In “Source Audio,” select the external audio input
source.
If the external audio input source is monaural:
Audio Input1 (Mono), 2 (Mono): Selects the analog
audio signal from a mic, musical instrument or other
device connected to the analog audio inputs.
USB 1(Mono), 2(Mono): Selects the digital audio signal
from a computer connected via USB.
If the external audio input source is stereo:
Audio Input1/2(Stereo): Selects the stereo analog audio
signal from a musical instrument or other device
connected to the analog audio inputs.
USB 1/2(Stereo): Selects the digital audio signal from a
computer connected via USB.
4. Specify whether you want to apply an insert effect to
the input source (i.e., to record the processed signal).
Choose the insert effect you want to use. If you don’t
want to use an effect, turn this Off.)
Note: If you’re using more than one insert effect, make
settings for the Insert FX page Chain parameters after
you execute Auto HDR/Sampling Setup . For the last
insert effect in the chain, set the REC Bus to 1 (for a
mono source) or 1/2 (for a stereo source). (At this time,
you will normally set
Bus Select to Off –but you don’t
have to do so.)
Note: You can also record the input source to an audio
track without applying an insert effect, and then send the
output of the audio track through an insert effect. Make
the appropriate
Bus Select setting in the IFX– Audio
Routing 1 page for the audio track you recorded.
5. Use “Recording Track” to specify the track(s) that
will be recorded.
If “Source Audio” is set to Audio Input 1 (Mono) or 2
(Mono), or R (Mono), or USB 1 (Mono) or 2 (Mono),
choose from Audio Track 1–16.