120
Program operating mode
Page 17 - LFO1
Amp EG ‘Time’ modulation
These
parameters
let
you
use
an
alternate
modulation
source
to
modify
the
amp
EG
times
that
were
specified
in
119.
AMS1(T) (Alternate Modulation Source 1 - Time)
This
parameter
specifies
the
source
that
will
control
the
“Time”
parameters
of
the
amp
EG
(see
123).
With
a
set
‐
ting
of
Off,
there
will
be
no
modulation.
Intensity
This
parameter
specifies
the
depth
and
direction
of
the
effect
that
“AMS1”
will
have.
For
example,
if
“AMS1(T)”
is
Amp
KTrk
+/+,
the
(Amp)
Keyboard
Track
settings
(see
will
control
the
EG
“Time”
parameters.
With
positive
(+)
values
of
this
parameter,
positive
(+)
values
of
“Ramp
(Ramp
Setting)
will
cause
EG
times
to
be
lengthened,
and
negative
(–)
values
of
“Ramp
(Ramp
Setting)”
will
cause
EG
times
to
be
shortened.
The
direction
of
the
change
is
specified
by
and
When
“AMS1(T)”
is
Velocity,
positive
(+)
values
will
cause
EG
times
to
lengthen
as
you
play
more
strongly,
and
negative
(–)
values
will
cause
EG
times
to
shorten
as
you
play
more
strongly.
With
a
setting
of
0,
the
EG
times
will
be
as
specified
by
the
parameters
(see
Attack Time Swing
This
parameter
specifies
the
direction
of
the
effect
that
“AMS1”
will
have
on
With
positive
(+)
values
of
“Intensity”,
setting
this
parameter
to
+
will
allow
AMS1
to
lengthen
the
time,
and
setting
it
to
–
will
allow
AMS1
to
shorten
the
time.
With
a
setting
of
0
there
will
be
no
effect.
Decay Time Swing
This
parameter
specifies
the
direction
of
the
effect
that
“AMS1”
will
have
on
With
positive
(+)
values
of
“Intensity”,
setting
this
parameter
to
+
will
allow
AMS1
to
lengthen
the
time,
and
setting
it
to
–
will
allow
AMS1
to
shorten
the
time.
With
a
setting
of
0
there
will
be
no
effect.
Slope Time Swing
This
parameter
specifies
the
direction
of
the
effect
that
“AMS1”
will
have
on
With
positive
(+)
values
of
“Intensity”,
setting
this
parameter
to
+
will
allow
AMS1
to
lengthen
the
time,
and
setting
it
to
–
will
allow
AMS1
to
shorten
the
time.
With
a
setting
of
0
there
will
be
no
effect.
Release Time
This
parameter
specifies
the
direction
of
the
effect
that
“AMS1”
will
have
on
With
positive
(+)
values
of
“Intensity”,
setting
this
parameter
to
+
will
allow
AMS1
to
lengthen
the
time,
and
setting
it
to
–
will
allow
AMS1
to
shorten
the
time.
With
a
setting
of
0
there
will
be
no
effect.
AMS2 (Alternate Modulation Source 2)
This
is
another
alternate
modulation
source
for
the
Amp
EG.
See
above
“AMS1”
parameters.
PAGE 17 - LFO1
In
this
and
the
next
page
you
can
make
settings
for
the
LFO
that
can
be
used
to
cyclically
modulate
the
Pitch,
Filter,
and
Amp
of
each
oscillator.
There
are
two
LFO
units
for
each
oscillator.
By
setting
the
LFO1
or
LFO2
Intensity
to
a
negative
(–)
value
for
Pitch,
Filter,
or
Amp,
you
can
invert
the
LFO
waveform.
Wave
This
parameter
selects
the
LFO
waveform.
The
num
‐
bers
that
appear
at
the
right
of
some
of
the
LFO
wave
‐
forms
indicate
the
phase
at
which
the
waveform
will
begin.
Frequency
Set
the
LFO
frequency.
A
setting
of
99
is
the
fastest.
00…99
Frequency
rate.
Amp 1 EG changes (Time) (AMS=Velocity, Intensity= a positive (+) value)
Amp 1 EG changes (Time)
(AMS=Amp KTrk +/+, Intensity = a positive (+) value)
(When Amp Keyboard Track “Low Ramp”= a positive (+) value, and
“High Ramp” = a positive (+) value)
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
Low-pitched note played with
Attack, Decay, Slope, and
Release Time Swing at +
Softly played note with
Attack, Decay, Slope and
Release Time Swing at +
High -pitched note played with
Attack, Decay, Slope, and
Release Time Swing at –
Strongly played note with
Attack, Decay, Slope and
Release Time Swing at +
Strongly played note with
Attack, Decay, Slope and
Release Time Swing at –
Triangle wave
Phase will change
randomly at each key-in
Sawtooth down
Square wave
Sine wave
Guitar vibrato
Triangle 0
Triangle 90
Triangle
Random
Saw 0
Saw 180
Square
Sine
Guitar
Exponential
Triangle
Exponential
Saw Down
Exponential
Saw Up
Step Triangle – 4
Step Triangle – 6
Step Saw – 4
Step Saw – 6
Random1 (S/H):
Conventional sample & hold (S/H) in which the
level changes randomly at fixed intervals of
time
Random2 (S/H):
Both the levels and the time intervals will
change randomly.
Random3 (S/H):
The maximum level and minimum level will
alternate at random intervals of time (i.e., a
square wave with random period).
Random4 (Vector)
Random5 (Vector)
Random6 (Vector)
These types cause Random 1–3 to change
smoothly. They can be used to simulate the
instability of acoustic instruments etc.
Summary of Contents for microARRANGER
