Korg M3, Parameter Manual

Page: 490 / 647

Effect Guide
480
061: Tape Echo
This effect simulates a tape echo unit with three playback
heads. The distortion and tonal change typical of magnetic
tape are also reproduced.
a: Delay (Tap1) [msec]
a: Src
a: Amt
b: Tap2 Position [%]
b: Tap3 Position [%]
The delay time for Tap 2 and 3 is specified as a proportion
(%) relative to Delay (Tap1). Even if you use dynamic
modulation to control Delay (Tap1), Tap 2 and 3 will change
at the same proportion.
d: FB Amt
e: FB Amt
f: FB Amt
g: Feedback
The feedback output from Tap 1, 2, and 3 is mixed according
to the FB Amt, and then the final amount of feedback is
specified by Feedback.
062: Auto Reverse
This effect records the input signal and automatically plays
it in reverse (the effect is similar to a tape reverse sound).
a: Rec Mode
b: Reverse Time [msec]
When Rec Mode is set to Single, you can set up to 2,640msec
for Reverse Time. If recording starts during the reverse
playback, the playback will be interrupted.
When Rec Mode is set to Multi, you can make another
recording during the reverse playback. However, the
maximum Reverse Time is limited to 1,320msec.
If you wish to record a phrase or rhythm pattern, set Rec
Mode
to Single. If you record only one note, set Rec Mode
to Multi.
The Reverse Time parameter specifies the maximum
duration of the reverse playback. The part in excess of this
limit will not be played in reverse. If you wish to add short
pieces of the reverse playback of single notes, make the
Reverse Time
shorter.
a
Delay (Tap1)
[msec]
0...2700
Sets the delay time (tap1)
p.480
Src Off...Tempo
Selects the modulation source
of the delay time
p.480
Amt
–2700...
+2700 Sets the modulation amount of
delay time
p.480
b
Tap2
Position [%]
0...100
Sets the position of Tap 2
relative to the Tap 1 delay time
the depth of pitch variation
p.480
c
Tap3
Position [%]
0...100
Sets the position of Tap 3
relative to the Tap 1 delay time
the depth of pitch variation
p.480
d
Tap1 Level 0...100 Sets the Tap1 output level
Pan L, 1...99, R Sets the stereo image of tap1
FB Amt –100...+100
Sets the Tap1 feedback amount
p.480
e
Tap2 Level 0...100 Sets the Tap2 output level
Pan L, 1...99, R Sets the stereo image of tap2
FB Amt –100...+100
Sets the Tap2 feedback amount
p.480
f
Tap3 Level 0...100 Sets the Tap3 output level
Pan L, 1...99, R Sets the stereo image of tap3
FB Amt –100...+100
Sets the Tap3 feedback amount
p.480
g
Feedback 0...100
Sets the amount of feedback
for Taps 1, 2, and 3
p.480
Src Off...Tempo
Selects the modulation source
of feedback amount
Amt –100...+100 Sets the feedback amount
h
High Damp
[%]
0...100
Sets the damping amount in
the high range
Low Damp
[%]
0...100
Sets the damping amount in
the low range
i Saturation 0...100 Sets the distortion amount
j
Input Trim 0...100 Sets the input gain
Pre Tone 0...100 Sets the tone of the input
k
Wow Flutter
[Hz]
0.02...1.00
Sets the frequency at which
pitch variation will occur
Wow Flutter
depth
0...100
Sets the depth of pitch
variation
l
Wet/Dry
Dry,
1 : 99...99 : 1,
Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount
for Wet/Dry
Wah Flatter
D -mod
Tap2/3
Position
+ Tape
Saturation
Left
Right
Wet / Dry
Trim
Pan Level
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Feedback
Feedback Amt
High / Low Damp Pre Tone
Delay
(1)
(2)
(3)
Delay Time
a Rec Mode Single, Multi
Sets the recording mode
p.480
b
Reverse Time
[msec]
20...2640
Sets the maximum duration of
the reverse playback
p.480
c
Envelope
Select D-mod,
Input
Selects whether the start and
end of recording is controlled
via the modulation source or
the input signal level
p.481
Src Off...Tempo
Selects the modulation source
that controls recording when
Envelope Select is set to D-mod
p.481
d Threshold 0...100
Sets the recording start level
when Envelope Select is set to
Input
p.481
e Response 0...100
Sets the speed of the response
to the end of recording
p.468
f Direct Mix
Always On,
Always Off,
Cross Fade
Selects how a dry sound is
mixed
p.468
g
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount
for Wet/Dry
Input
D-mod
Envelope Select
D -mod
Envelope Control
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Auto Reverse
Direct
Mix
Rec/Reverse Play
Control