Korg M3, Parameter Manual

Page: 488 / 647

Effect Guide
478
b: D-mod Modulation
When the modulation source is used for control, this
parameter reverses the left and right modulation direction.
d: LFO Sync
d: Src
h: L LFO Phase [deg]
i: R LFO Phase [deg]
If LFO Sync is On, the LFO will be reset by the modulation
source that is received.
The Src parameter sets the modulation source that resets the
LFO. For example, you can assign Gate as a modulation
source so that the sweep always starts from the specified
point.
L LFO Phase
and R LFO Phase set the phase obtained when
the left and right LFOs are reset. In this way, you can create
changes in pitch sweep for the left and right channels
individually.
The effect is off when a value of the modulation source
specified in the Src parameter is 63 or smaller, and the
effect is on when the value is 64 or higher. The LFO is
triggered and reset to the L LFO Phase and R LFO
Phase
settings when the value changes from 63 or
smaller to 64 or higher.
059: St. Dynamic Delay
(Stereo Dynamic Delay)
This stereo delay controls the level of delay according to the
input signal level. You can use this as a ducking delay that
applies delay to the sound only when you play keys at a
high velocity or only when the volume level is low.
a: Control Target
This parameter selects no level control, delay output control
(effect balance), or feedback amount control.
a: Polarity
b: Threshold
b: Offset
c: Attack
d: Release
The Offset parameter specifies the value for the Control
Target
parameter (that is set to None), expressed as the ratio
relative to the parameter value (the Wet/Dry value with
Control Target
= Output Level, or the Feedback value with
Control Target = Feedback).
When Polarity is positive, the Control Target value is
obtained by multiplying the parameter value by the Offset
value (if the input level is below the threshold), or equals the
parameter value if the input level exceeds the threshold.
When Polarity is negative, Control Target value equals the
parameter value if the input level is below the threshold, or
is obtained by multiplying the parameter value by the
Offset
value if the level exceeds the threshold.
The Attack and Release parameters specify attack time and
release time of delay level control.
l
Wet/Dry
–Wet...
–1 : 99, Dry,
1 : 99...Wet Sets the balance between the
effect and the dry input
p.450
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount
for Wet/Dry
a
Control
Target None, Out,
FB Selects from no control, output,
and feedback
p.478
Polarity +, – Reverses level control p.478
b
Threshold 0...100
Sets the level to which the
effect is applied
p.478
Offset 0...100
Sets the offset of level control
p.478
c Attack 1...100
Sets the attack time of level
control
p.478
d Release 1...100
Sets the release time of level
control
p.478
e
L Delay Time
[msec]
0.0...1360.0
Sets the delay time for the left
channel
f
R Delay Time
[msec]
0.0...1360.0
Sets the delay time for the right
channel
g Feedback –100...+100 Sets the feedback amount
h
High Damp
[%]
0...100
Sets the damping amount in
the high range
p.476
Low Damp
[%]
0...100
Sets the damping amount in
the low range
p.476
i Spread –100...+100
Sets the width of the stereo
image of the effect sound
p.476
j
Wet/Dry
Dry,
1 : 99...99 : 1,
Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount
for Wet/Dry
Delay
Left
Right
Feedback
Spread
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
High Damp Low Damp
High Damp Low Damp
Threshold
Delay
FB Out
Control Target
Attack, Release Envelope
+