Korenix JetNet 7852G-4XG Series User Manual Download Page 868

Page: 868 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 868/1568

8.2.2

Configuration Commands

8.2.2.1

ip igmp

This command sets the administrative mode of IGMP in the router to active

Syntax

ip igmp
no ip igmp

no -

This command sets the administrative mode of IGMP in the router to inactive.

Default Setting

Disabled

Command Mode

Global Config

This command sets the administrative mode of IGMP on an interface to active

Syntax

ip igmp
no ip igmp

no -

This command sets the administrative mode of IGMP on an interface to inactive.

Default
Setting

Disabled

Command

Mode

Interface Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands