Korenix JetNet 7852G-4XG Series User Manual Download Page 701

Page: 701 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 701/1568

7.3.2

Configuration Commands

7.3.2.1

router ospf

Use this command to enter Router OSPF mode

Syntax

router ospf

Default Setting

None

Command Mode

Global Config

7.3.2.2

enable

Use

enable

command resets the default administrative mode of OSPF in the router (active).

no enable

command sets the administrative mode of OSPF in the router to inactive

Syntax

enable
no enable

Default
Setting

Enable

Command

Mode

Router OSPF Config Mode

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands