Korenix JetNet 7852G-4XG Series User Manual Download Page 40 | Manualshive

Page: 40 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 40/1568

5

Command Line Interface Structure and

Mode-based CLI

The Command Line Interface (CLI) syntax, conventions, and terminology are described in this section.
Each CLI command is illustrated using the structure outlined below.

5.1

CLI Command Format

Commands are followed by values, parameters, or both.

Example 1

ip address <ipaddr> <netmask> [<gateway>]



ip address

is the command name.



<ipaddr> <netmask>

are the required values for the command.



[<gateway>]

is the optional value for the command.

Example 2

snmp-server location <loc>



snmp-server location is the command name.



<loc>

is the required parameter for the command.

Example 3

clear vlan



clear vlan

is the command name.

Command

The text in bold, non-italic font must be typed exactly as shown.

«
...
38
39
40
41
42
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: YASKAWA Pages: 68

InterReach Fusion ADCP-77-044

Brand: TE Connectivity Pages: 236

Brand: Amperes Pages: 8

Barricade SMC7901WBRA2

Brand: SMC Networks Pages: 2

Brand: Watchguard Pages: 30

Anybus Communicator ABC4021

Brand: HMS Networks Pages: 60

Brand: Kanguru Pages: 13

Brand: Infoblox Pages: 13

JetNet 3508-LVDC

Brand: Korenix Pages: 16

Brand: IBM Pages: 34

Brand: eWON Pages: 34

Brand: CalAmp Pages: 115

Brand: Waver Pages: 36

Brand: Microtek Pages: 25

Brand: FiberHome Pages: 44

ACC-BKT-AX-BEAM

Brand: Extreme Networks Pages: 35

Brand: N-Tron Pages: 2

Brand: Datavideo Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands