Korenix JetNet 7852G-4XG Series User Manual Download Page 1371

Page: 1371 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1371/1568

11.5.5

Managing Class of Service

11.5.5.1

Configuring Trust Mode Configuration Page

Selection Criteria

Interface

- Specifies all CoS configurable interfaces. The option "Global" represents the most recent

global configuration settings. These may be overridden on a per-interface basis.

Interface Trust Mode

- Specifies whether or not to trust a particular packet marking at ingress.

Interface Trust Mode can only be one of the following:



untrusted



trust dot1p



trust ip-dscp

Default value is trust dot1p.

Non-Configurable Data

Untrusted Traffic Class

- Displays traffic class (i.e. queue) to which all traffic is directed when in

'untrusted' mode. Valid Range is (0 to 7).

Non-IP Traffic Class

- Displays traffic class (i.e. queue) to which all non-IP traffic is directed when in

'trust ip-precedence' or 'trust ip-dscp' mode. Valid Range is (0 to 7).

Current 802.1p Priority Mapping

- Displays the current 802.1p priority mapping configuration.

Command Buttons

«
...
1369
1370
1371
1372
1373
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands