Korenix JetNet 7852G-4XG Series User Manual Download Page 1082 | Manualshive

Page: 1082 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1082/1568

11.2.7

Viewing Statistics

11.2.7.1

Viewing the whole Switch Detailed Statistics Page

Non-Configurable Data

ifIndex

- This object indicates the ifIndex of the interface table entry associated with the Processor of

this switch.

Octets Received

- The total number of octets of data received by the processor (excluding framing

bits but including FCS octets).

Packets Received Without Errors

- The total number of packets (including broadcast packets and

multicast packets) received by the processor.

Unicast Packets Received

- The number of subnetwork-unicast packets delivered to a higher-layer

protocol.

Multicast Packets Received

- The total number of packets received that were directed to a

multicast address. Note that this number does not include packets directed to the broadcast address.

Broadcast Packets Received

- The total number of packets received that were directed to the

broadcast address. Note that this does not include multicast packets.

Receive Packets Discarded

- The number of inbound packets which were chosen to be discarded

even though no errors had been detected to prevent their being deliverable to a higher-layer
protocol. A possible reason for discarding a packet could be to free up buffer space.

Octets Transmitted

- The total number of octets transmitted out of the interface, including framing

characters.

Packets Transmitted Without Errors

- The total number of packets transmitted out of the interface.

Unicast Packets Transmitted

- The total number of packets that higher-level protocols requested

be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.

«
...
1080
1081
1082
1083
1084
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: Ubiquiti Pages: 50

Brand: IBM Pages: 32

JetWeb JX2-PR0FI1

Brand: Jetter Pages: 67

Brand: Cisco MERAKI Pages: 4

Brand: Gigabyte Pages: 18

Brand: BHU NETWORKS Pages: 75

Brand: US Robotics Pages: 180

Brand: Comtrend Corporation Pages: 4

Brand: Linksys Pages: 6

Brand: MaxComm Pages: 10

Brand: PairGain Pages: 80

Brand: NETGEAR Pages: 152

Brand: DPS Pages: 57

IP Board IPT10000C

Brand: Dialogic Pages: 2

Brand: Nexxt Pages: 2

Brand: Acard Pages: 43

Brand: Data-Tronix Pages: 15

Brand: Adeunis RF Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands