background image

6

Major Component Replacements

KNHE28

K2NHE28

Blower/Motor Assembly

KBB36

K2BB36

Capacitor

0452-03

0452-03

Blower Motor

0261-120

0261-121

Coil

0666-35

0666-35

Accessories

Automatic Water Flow Control

High Water Level Detector

Internal corrosion resistant coatings

Low Airflow Detector

Other voltages and frequencies

Special materials or finishes

Special motors, line cords or
connectors

Temperature Alarm

6 2
8 4

7 3

1 0

BLOWER

MTR

LEVEL SWITCH

SOLENOID

WE

BK

BK

BK

BL

WE

RELAY

STD. PLUG
WITH GND.

N.O.

CAPACITOR

N.O.

N.C.

ALARM

TSTAT

AIR FLOW SWITCH

BLOCK

TERM.

TSTAT

CONT.

OPTIONS

Wiring Diagram

WD-394

NOTE: Part Numbers shown are for 60Hz/1Ø. For 50Hz consult Kooltronic.

Technical Data

* 60 Hz. operation. For 50 Hz operation, consult Kooltronic.

Model

Volts

Power

Amps

Watts

Maximum Inlet

Water Temp.

ºF (ºC) 

Performance

Watts/ºF (Watts/ºC)

1 GPM

2 GPM

BTU/H (Watts) @

95ºF(35ºC) Enclosure Air Temp.

50ºF(10ºC) Inlet Water Temp.

1 GPM

2 GPM

Approx.

Weight

lbs. (kg.)

KNHE28

115

1.2

140

85 (29)

42 (76)

50 (38.7)

6,449 (1,890)

7,677 (2,250)

44 (20)

K2NHE28

230

0.6

140

85 (29)

42 (76)

50 (38.7)

6,449 (1,890)

7,677 (2,250)

44 (20)

Note: The rating Watts/°F is the heat dissipation divided by temperature difference between maximum air temperature in 

enclosure and water temperature entering the heat exchanger.

Summary of Contents for KNHE28 Series









Reviews: