background image

4

IV. Product Identification and Nameplate

Each Kooltronic Air Conditioner includes an identification nameplate. This nameplate provides:

q

Model Number

w

Serial Number

e

Cooling capacity

r

Heating capacity (Optional)

t

Electrical power characteristics

y

Type and amount of refrigerant required for recharging

u

Design Pressure

i

Maximum and minimum ambient operating temperatures

o

Manufacturing Order Number

a

Filter Part Number

s

Underwriters Laboratories Inc. Listed or Recognized Marks and NEMA ratings

We recommend you copy this information from your unit.

qwo

When ordering parts, specify the Model Number, Serial Number & MFG. Order Number.

t

Before operating, be sure that the power source matches these requirements.

y

Use of incorrect type or amount of refrigerant will adversely affect performance and may damage the unit.

Make sure that these parameters are met. Failure to do so may result in permanent damage to the unit.

SERVICE AIR FILTER REGULARLY

UL RECOGNIZED AND CSA CERTIFIED FOR USE WITH CLASS I, DIVISION 1, GROUPS A, B, C AND D

HAZARDOUS LOCATIONS, TYPE X PURGE AND CLASS I, DIVISION 2, GROUPS A, B, C AND D,

TYPE Z PURGE ENCLOSURES WHEN INSTALLED ON AN APPROVED PRESSURIZED ENCLOSURE

AND CONNECTED TO PURGE/PRESSURIZATION CONTROL SYSTEM PER NFPA496

ALSO SUITABLE FOR CLASS I, ZONE 2, GROUPS IIA, IIB PLUS HYDROGEN AND IIC

AIR LEAKAGE @ 0.5 I.W.G. PRESSURE CFM - 0.4

INTERNAL PRESSURIZED VOLUME CU. FT. - 10.8

ALL MOTORS ARE THERMALLY PROTECTED

UNAUTHORIZED SERVICE OR MODIFICATION VIOLATES WARRANTY

NEMA/EEMAC/UL50 BY UNDERWRITERS LABORATORIES, INC. TYPE 1

SPECIAL PURPOSE AIR CONDITIONER EQUIPMENT COMPARTMENT ONLY

TYPE 3R, 12 & 4/4X INTERFACE TO THE ELECTRICAL ENCLOSURE ONLY

NEMA/EEMAC/UL50 BY UNDERWRITERS LABORATORIES, INC.

SPECIAL PURPOSE AIR CONDITIONER

OUTDOOR USE      ALLOW 5 MINUTES BEFORE RESTARTING AFTER SHUTDOWN

Air Conditioner

KOOLTRONIC, INC.   PENNINGTON, NJ

MANUFACTURED BY:

Heating BTU/H:

Cooling BTU/H:

Max:

Ambient Temperature: Min:

P.S.I.G.

P.S.I.G.

Design Pressure, Low Side:

Design Pressure, High Side:

Oz. Factory Charge

Refrigerant:

Max. Fuse Size / HACR Type Circuit Breaker:

Min. Circuit Ampacity:

Watts:

Amps:

Volts

Electric Heater:

R.L.A.:

L.R.A.:

Volts

Compressor:

Amps:

Hp:

Volts

Condenser Fan Motor:

Amps:

Hp:

Volts

Evaporator Fan Motor:

Hertz:

Phase:

Volts

Mfg. Order No.:

Rated Voltage:

Serial No.

Model No.

Filter P/N:

ALSO SUITABLE FOR CLASS I, ZONE 1, GROUPS IIA, IIB PLUS HYDROGEN AND IIC

LISTED 84H7

SPECIAL PURPOSE

AIR CONDITIONER

y

y

q

w

u

a

s

o

r

e

t

t

t

t

t

t

t

t

t

t
t

t

t

t

t
t

t

i

u

i

Summary of Contents for Hazardous Location K3A4C12HL56LV




















Reviews: