Kontron AT8902M User Manual Download Page 69

Page: 69 / 92

AT8902M

Software Description

Page 4 - 4

AT8902M User Guide

4.1.2

Switching

• IEEE 802.3ac - VLAN Tagging

• IEEE 802.3ad - Link Aggregation with Static LAG and LACP support

• IEEE 802.1S - Multiple Spanning Tree

• IEEE 802.1W - Rapid Spanning Tree

• IEEE 802.1D - Spanning Tree

• GARP

• GVRP - Dynamic VLAN Registration

• GMRP - Dynamic L2 Multicast Registration

• IEEE 802.1Q - Virtual LANs with Port Based VLANs

• IEEE 802.1v - Protocol based VLANs

• IEEE 802.1p - Ethernet Priority with User Provisioning & Mapping

• IEEE 802.1X - Port Authentication

• IEEE 802.3x - Flow Control

• IGMP Snooping

• Port Mirroring

• Broadcast Storm Recovery

• Static MAC Filtering

• Double VLAN / vMAN Tagging

• Jumbo Frames

• IPv6 Classification APIs

• XMODEM

• RFC 768 - UDP

• RFC 783 - TFTP

• RFC 791 - IP

• RFC 792 - ICMP

• RFC 793 - TCP

• RFC 951 - BOOTP

• RFC 1321 - Message Digest Algorithm (MD5)

Summary of Contents for AT8902M





























































































Search results

Summary of Contents for AT8902M

Reviews:

Brands by name

Popular brands

Kontron AT8902M, User Manual

Search results

Summary of Contents for AT8902M

Reviews:

Brands by name

Popular brands