2. ASSEMBLY & HANDLING
CROSS SUPPORT
c
2.7
Take the four bushings
f.3
and
g.3
from the
2.7
accessory bags and insert them into the
2.7
upper side holes of the extension tube
b
2.7
gesteckt
2.8
The U-sheet of the cross support
c
2.8
is pushed over these bushings until
2.8
the holes are aligned.
2.9
Fix upper clamp:
2.9.1
Push washer
f.2
over the square of
2.9.1
the screw
f.1
and then insert it through
2.9.1
the upper bushings
f.3
…
2.9.2
…and lock it by means of the washer
f.4
2.9.2
and lock nut
f.5
.
2.9.2
Use wrench SW13
f.7
for this purpose.
2.9.2
Finally, press on the protective cap
f.6
.
2.10
Fix the lower clamp:
2.10.1
Slide washer
g.4
over the square
2.10.1
of the screw
g.5
and now push it
2.10.1
through the bushings
g.3
from the
2.10.1
other side than above…
2.10.2
…and lock it by means of the
2.10.2
washer
g.2
and clamp lever
g.1
.
ADJUSTMENT BRACKETS
d
,
e.3
2.11.1
First remove wing
2.11.1
screw
d.3
and washer.
2.11.2
Press cap
e.3
into the
2.11.2
open tube end below
2.11.2
the retaining bracket.
2.11.3
Push tube socket into an
2.11.3
opening of the cross support
c
2.11.3
and…
2.11.4
…secure position by
2.11.4
screwing in wing
2.11.4
screw with washer
2.11.4
from
2.11.1
again
2.11.5
Proceed with the other adjust-
2.11.5
ment bracket in the same way
EQUIPMENT STOP
e.4/5/6/7
NOTES
To ensure that the equipment stops
e.7
can fulfill their
function as safety elements, please observe the following:
- One stop is provided for each adjustment bracket
- The stop must be at the bottom when the support is inclined;
-
if not, it must be remounted accordingly
- To prevent the stop from rotating away unintentionally,
-
the foot of the bracket must never be mounted on top
-
of the bracket, but always underneath it.
2.12.1
Place the foot of the first equipment stop
e.7
2.12.1
against the (lower) hole of the bracket from below.
2.12.2
Insert the slotted screws
e.6
from above through
2.12.2
the bracket, the foot of the stop and the washer
e.5
.
2.12.2
Use the hexagon nut
e.4
to secure the connection.
2.12.3
Now attach the second equipment stop to the other
2.12.3
bracket (bottom) in the same way.
FELT STRIPS
e.1/2/8
Felt strips are placed on the brackets to match the
dimensions and shape of the load (e.g. the mixer’s)
2.13.1
The thin felts (
e.1
peel off foil) stick to the wall of
2.13.1
the brackets (flush at the top).
2.13.2
The thick felts (
e.2
peel off foil) are attached to
2.13.2
the bottom of the brackets.
2.13.3
The small felts (
e.8
peel off foil) are placed on
2.13.3
the equipment stops.
28075 Mixer stand
ADJUSTMENT BRACKETS
d
,
e.3
EQUIPMENT STOP
e.4/5/6/7
FELT STRIPS
e.1/2/8
CROSS SUPPORT
c