26709 Additional weight
for base plates
INTENDED USE
- The additional load is a professional mean to increase the stability of
-
K&M speakers and monitor stands that are equipped with M20 base plates.
- The centrally located bore of the additional weight is used for mounting
-
on the stand, the additional bore enables a visually appealing cable
-
laying beneath the suitable base plates 26703, 26704, 26705 and 26706.
FEATURES & CAPABILITIES
- The additional weight can be used for
-
- the K&M stands: 24624, 26734, 26735, 26737, 26740, 26750
-
- the K&M base plates: 26700, 26703, 26704, 26705 and 26706
- For potential cable bushing there is another bore in the plate
- Four rubber buffers ensure non-slip and low-noise operation
- Dimensions: ø 325 mm, 8 mm thick, bores: ø 43 mm, weight: 5 kg
SAFETY INSTRUCTIONS
Thank you for choosing this product. Please read and follow these instructions carefully
before installation and use. They inform you about all important steps regarding assembly
and handling. We recommend that you keep them for future reference.
A. GENERAL
A.
-
CAUTION! The net weight of 5 kg and the edges of the product can pose a
A.
-
risk to persons and property.
A.
-
Careful and attentive handling during installation and operation, dismantling,
A.
-
transport and storage is therefore indispensable
A.
-
In particular, DO NOT drop the additional weight and avoid hand/finger injuries.
A.
- The additional weight may only be used with the intended K&M stands and base
A.
-
plates (see above FEATURES & CAPABILITIES)
A.
- Please also observe the user instructions for use and safety indication pertaining to
A.
-
to these stands and base plates
A.
- Pay particular attention that the additional weight does NOT push itself between
A.
-
the screw connection of the stand tube and plate
4.4.3
A.
- Assembly and handling may only be carried out by (technical and physically fit)
A.
-
suitable personnel
A.
- For indoor use only
B. PREDICTABLE MISUSE
B.
- The dimensions (ø 325 mm, ø 43 mm) of the additional weight are perfectly
B.
-
matched to K&M stands and base plates. For this reason, it cannot be used
B.
-
with other products. This also applies to:
B.
-
- K&M products with other dimensions, especially microphone stands with base
B.
-
-
plates. The secure fitting of the additional weight cannot be guaranteed
B.
-
- For non-K&M products
INSTALLATION INSTRUCTIONS
1. COMPONENTS
The additional weight consists of a circular steel plate, covered with four rubber feet
(bumpons). There are no other components.
2. PREPARING The ADDITIONAL WEIGHT
Please carry out a visual inspection to ensure that all parts are complete and - if
recognizable - in order. Damaged parts must not be reused, they must be replaced
or repaired by qualified personnel.
3. PREPARING THE STANDS/BASE PLATES
3.1
If necessary, detach the base plate from the stand tube and place it on a suitable
3.1
surface.
3.2
Carry out a visual inspection of the base plates. Defective bases must not be used;
3.2
they should be replaced or repaired by qualified personnel.
3.3
There should be no objects, dirt etc. on the base plate; we recommend a thorough
3.3
cleaning before using the additional weight.
4. MOUNTING THE ADDITIONAL WEIGHT
4.1
Place the additional weight on the base plate with the rubber feet downwards.
4.2
Align the additional weight so that the central hole is exactly located above the
4.2
likewise central M20 screw socket of the base plate.
4.3
Position the base tube with M20 threaded bolts and screw it into the socket plate
4.3
whilst readjusting the position of the additional weight if necessary.
4.4 WARNING! DANGER OF TILTING IN CASE OF FAULTY INSTALLATION
4.4.1
Make sure that the base tube is inserted into the bore hole of the additional
4.4.1
weight and is screwed gap free to the base plate (0).
4.4.2
Check condition whilst slightly lifting the additional weight.
4.4.3
If the additional weight has shoved itself between the base plate and the
4.4.3
base tube there will be gap (X) which prevents a secure screw-fitting.
4.4.3
Please make sure to correct: see
4.4.1
3. PREPARING THE STANDS/BASE PLATES
4. MOUNTING THE ADDITIONAL WEIGHT
4.4 WARNING! DANGER OF TILTING IN CASE OF FAULTY INSTALLATION
Example
K&M 26703 Base plate
410 x 410 x 27.3 mm
