KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
23840-300-55 Rev.1a 03-80-421-00 6/20
INSTALLATION
OPERATING MODE
TECHNICAL DATA
1
Screw the table clamp to the panel
2
Insert the rod of the microphone arm into the opening
2
of the table clamp and adjust the direction of the arm
2.a
Secure this position by tightening the knurled screw
3
Select threaded connection (3/8", 5/8") and attach microphone
4
Set the microphone arm as described in OPERATING MODE
The proper functioning of the microphone arm is based on the
interaction of three factors.
A. MICROPHONE WEIGHT
B. SPRING TENSION
C. STRENGTH OF KNURLED NUTS
6
5
Without microphone and loosen knurled nuts the arms point
5
towards the ceiling - this is due to the spring preload.
5
- The load of the microphone counteracts the spring preload,
5
-
so that the arm more or less exactly meets the desired
5
-
position.
5
- This mechanism works best with microphones with the nominal
5
-
load of nearly 0.8 kg. This load acts on the spring preload, so
5
-
that almost any possible position can be reached.
6
In order for the microphone to maintain the intended position,
6
tighten slightly the three knurled nuts - only to much so as to
6
prevent the arms from moving independently.
7
If the balance is correct, the microphone arm can be moved in
7
several desired positions - avoiding the screwing and unscrewing
7
of the knurled nuts
6
.
WIRING
The 23840 Microphone desk arm contains no wiring.
Four cable clamps are included to fix a subsequently
mounted cable (see accessory bag).
8
Clip the four cable clamps onto the desired position
8
on the arm profile.
9
Once fitted, these clamps can be moved continuously
9
on the arms.
Material
Microphone arms: square steel profile, black
Springs, small parts: steel, black
Guides, handles: plastic, black
table clamp housing: aluminium, PA, black
Dimensions
- max. delivery: 820 mm
- Arm lengths: 500 + 460 + 60 mm
- Table clamp: handle 45 mm, thread M8,
-
for panels: 20 - 51 mm, for tubes: ø 25 – 51 mm
- Microphone connectors: 3/8", 5/8"
Weight
1.38 kg
Box
H x W x D: 530 x 120 x 65 mm
Accessories (optional) Table flange 23855
23840 Microphone desk arm
- suitable for recording studios and multimedia activity areas
- smooth and flexible positioning of microphones
- load capacity: up to 0.8 kg; reach: up to 0.9 m
- with table clamp (max. board thickness 51 mm)
- threaded connections 3/8" and 5/8"
SAFETY INSTRUCTIONS
- Ensure a suitable support panel in terms of
-
thickness (max. 51 mm), texture and surface.
- The table clamp
1
must be firmly fixed.
- Maximum load capacity: 0.8 kg.
BEWARE OF UNCONTROLLED MOVEMENTS
- In an unloaded condition, the springs pulls up
5
the arms of
-
the Microphone holder (= starting position).
- In order to avoid this uncontrolled movement, the following
-
measures must be taken before removing the microphone
-
respectively before loosening the knurled nuts hold the
-
microphone arm
4
with your hand or bring in initial position.
- The tightening of the three knurled nuts
6
at the joints of the
-
Microphone is NOT sufficient to avoid this uncontrolled
-
movement since the spring force is too strong.
Thank you very much for choosing this product. Please read and follow the
instructions carefully before installing and operating this product. They inform
you about all important steps to ensure safe handling. Please keep these
instructions for future reference.
Initial
position
Mounting the
cable clamps
Setting
examples
