TESTING, MAINTENANCE
- During maintenance work, check for possible hazards (bumping, jamming).
- Clean with a slightly damp cloth and a non-abrasive cleaning agent.
FAULT-FINDING (F) and REPAIR (R )
F: Drum wobbles on stand B: Check drum for unevenness
B: Change the width of the stand
F: The width of the stand does not fit B: Adjust angle on the toothed joint
F: Drum does not lie on rubbers B: Shift rubbers accordingly
KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
13335-000-55 Rev.06 03-80-371-00 6/19
SAFETY INSTRUCTIONS
TECHNISCHE DATEN
Material
Tubes: steel, powder-coated, black
Screws, nuts, bolts - galvanised, nickel-plated
Toothed joint: zinc cast, powder coated, black
Parquet protectors, rubber pads - TPE, Shore 59A
Eccentric clamping lever - POM, black
Load
Marching drums, concert drums
Dimensions
Depth of support: 523/465 mm
Packaging
Carton: 790 x 580 x 135 mm
Weight
4.8 kg
STAND INSTALLATION
1
Install the stand so that both support tubes (with eight rubber pads) are at the top.
2
Fold up both clamping levers > the toothing have separated from each other.
3
Pull the support tubes apart until the desired height/width is reached.
4
Close the clamping lever > the gear teeth are engaged.
4.a
NOTE:
4.a
The tooth tips must not be pressed against each other. If necessary twist the
4.a
joints a little bit.
4.b
The clamping levers must be clapped beyond the eccentric point up to the stop. This
4.b
position is always mandatory, in particular during operation under load, but also
4.b
during transport and storage.
4.b
A protruding clamping lever is only permitted when the stand is opened or closed,
4.b
otherwise it indicates faulty position.
JOINT DISC WITH SCALE
5
The joint disks are finely toothed all around in steps of 5°
5
allowing 34 (!) installation versions of the stand.
6
By means of the scale and a marking (X) on the opposite side of the pulley
6
the position can be exactly determined.
6
A preferred installation version can easily be found again.
INSTALLATION VERSIONS & DIMENSIONS
7
A selection of the 34 installation versions is shown here.
7
NOTE: The height inevitably changes with the width.
8
The fully folded stand is suited for transport and storage owed to
8
compact dimensions.
TIPS FOR SAFE INSTALLATION
1
9
The diameter of the drum is always decisive.
19
This determines the width of the two support tubes of the stand.
19
The adjustment of a certain height is not permitted if these results
19
in an unsafe support of the drum.
10
The drum must always be placed centrally on the stand.
10
In case of protrusions these must be as uniformly spread.
11
Eight rubber protectors (four of them movable) ensure the
11
secure fitting of the instrument and protect its surface.
INSTALLATION & OPERATING INSTRUCTIONS
13335 Marching drum stand
Extremely high-quality stand - suited for all major marching and concert drums.
- excellent workmanship, smooth running and stability.
- the ergonomic clamping lever ensures easy opening and closing of the stand
- the flat package is ideal for mobile use and storage
- the robust metal joint is finely interlocked with 5° steps and allows a wide range of
-
different settings relating to height and width of the supports
- with the aid of a scale you can readily find your preferred installation option
- soft rubber caps and pads ensure a secure footing and protect the drum from scratches.
Thank you for choosing this product. This instruction manual informs you about the
important steps to set up and handle the product. We recommend to keep the manual in
a separate place for a possible later use.
- Other loads than marching and concert drums are not permitted.
- Before and after use of the stand please carry out a visual inspection regarding:
-
function, completeness and mobility.
- A damaged product must not be used unless a qualified repair has been carried out.
- Make sure that the surface is suitable, i.e. sustainable and level floor.
- The possibility to fold and adjust the product contains entrapment hazards.
-
Prudent and proper handling are indispensable during disassembly and reassembly
-
and operating.
- Before placing the instrument make sure that the toothed locked washers are
-
engaged and the eccentric clamping lever leans against the tube.
- The stand must be centrically loaded. Make sure you choose an adequate width
-
(see chapter: TIPS).
- The parquet protectors are made of high-quality material and are where possible free
-
of plasticizers. For the protection of sensitive floors (e.g. certain parquet types), a
-
anti-slip underlay should be used if necessary.
STAND INSTALLATION
JOINT DISC WITH SCALE
INSTALLATION VERSIONS & DIMENSIONS
TIPS FOR SAFE INSTALLATION
