Konica Minolta SRX-101A Operation Manual Download Page 26

Page: 26 / 31

24 OPERATION MANUAL

SERVICE AND MAINTENANCE

Turn the power breaker ON (Left on front below the

feed tray).

●

The RUN button lamp will go on.

• Do not press the RUN button.

Press the replenishment button (beaker) until the

READY lamp begins flashing (about 5 seconds).

●

It will take about 22 minutes for the tanks to be

filled.

As soon as the tanks are filled, the READY lamp

will stop flashing.

Fill the measuring cup exactly with 78

of starter

solution.

•Use the starter specified by the DEV solution.

Pour the starter solution into the starter solution

inlet in the developing tank.

Close the top cover.

RUN

READY

RUN

READY

RUN

™

Power Breaker

Press and hold
down for 5 seconds

™

Measuring Cup

™

Starter Solution

™

Starter Solution Inlet

Summary of Contents for SRX-101A
































Search results

Summary of Contents for SRX-101A

Reviews:

Related manuals for SRX-101A

Brands by name

Popular brands

Konica Minolta SRX-101A, Operation Manual

Search results

Summary of Contents for SRX-101A

Reviews:

Related manuals for SRX-101A

Brands by name

Popular brands