Konica Minolta magicolor 1600W Service Manual Download Page 84

Page: 84 / 216

Field Service

er. 1.0 Nov. 200

6. Other

magicolor 1600W magicolor 1650EN

Maintenance

6.4

Cleaning procedure

NOTE
• The alcohol described in the cleaning procedure represents the isopropyl alcohol.

6.4.1

Tray 1 media feed roller

Open the top cover.

Remove the imaging cartridge.

See P.13

Using a cleaning pad dampened with
alcohol, wipe the tray1 media feed
roller [1] clean of dirt.

6.4.2

Printer head window

Enter the [P/H CLEAN UP] mode.

For magicolor 1600W: See P.53
For magicolor 1650EN: See P.70

Open the top cover.

Remove the imaging cartridge.

See P.13

Clean P/H window [1] with soft cloth.

A034F2C516DA

[1]

A034F2C517DA

[1]

Summary of Contents for magicolor 1600W

























































































































































































































Search results

Summary of Contents for magicolor 1600W

Reviews:

Related manuals for magicolor 1600W

Brands by name

Popular brands

Konica Minolta magicolor 1600W, Service Manual

Search results

Summary of Contents for magicolor 1600W

Reviews:

Related manuals for magicolor 1600W

Brands by name

Popular brands