manualshive.com logo in svg

Kongsberg Simrad MF90, Installation Manual

Share
Download
Kongsberg Simrad MF90 Installation Manual Download Page 233

476671/B

231

Configuring the Operating Panel (Mk2)

The optional Operating Panel contains all necessary control functions for normal operation
of the MF90 system. Before it can be put to use, the Mk2 Operating Panel must be
configured to permit Ethernet communication between the panel and the Processor Unit.

The controls provided by the Operating Panel are arranged in logical functional groups. This
offers you clear and easy operation with fast access to key functionality. All the functionality
provided by the MF90 system can be accessed using the trackball on the Operating Panel
and the menu system shown in the display presentation.

Note

These tasks are only related to the Mk2 Operating Panel.

Topics

Setting up the Operating Panel (Mk2), page 231

Using more than one Operating Panel to control the sonar (Mk2), page 235

Using a single Operating Panel to control more than one sonar (Mk2), page 239

Setting up the Operating Panel (Mk2)

The Operating Panel offers all necessary control functions for normal operation. Before
it can be put to use, the Mk2 Operating Panel must be configured to permit Ethernet
communication between the panel and the Processor Unit.

Prerequisites

The Operating Panel is installed as specified in this manual. The Processor Unit is turned
on. The following specific items are required for this task:

• Computer mouse

• Computer keyboard

Neither tools nor instruments are required.

Context

When supplied, the Operating Panel is set up with the following communication parameters:

• IP Address: 157.237.60.20

• Subnet mask: 255.255.255.0

• Gateway: 157.237.60.1

Setting to work

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands