Kongsberg M3 Sonar Reference Manual Download | Manualshive

Page: 133 / 182

background image

922-20297001/1.2

131

•

Angle

Entering an angle is not necessary if the transducer face of the Sonar Head is
aligned with the rotator. However, if the Sonar Head is installed at an angle to
the rotator, then enter that value here.

Override Mounting Parameters

Enabling this option will apply the current offsets on this page during playback instead
of the offsets recorded in your data file.

Tip

If you apply the offset override, playback a file, then re-record a new file during
playback, the offsets will not be applied to the new re-recorded file (the new file will
use the original offsets). However, if you export data to a third-party application in
playback mode, the offset override will be applied to the exported data.

Related topics

System Configuration dialog box - Rotators Setup page, page 118

Functions and dialog boxes

«
...
131
132
133
134
135
...
»

Summary of Contents for M3 Sonar























































































































































































Reviews:

No comments

Related manuals for M3 Sonar

Brand: NORLUX Pages: 2

Brand: Makita Pages: 10

Brand: A.MENARINI Pages: 2

Brand: Far Tools Pages: 25

Brand: QRS Pages: 16

Brand: QMAXZ Lighting Pages: 36

Brand: Raytec Pages: 60

Chicken Coop Plan 3x5

Brand: EASY COOPS Pages: 21

Chicken Coop Plan 4x6

Brand: EASY COOPS Pages: 18

Chicken Coop Plan 8x10

Brand: EASY COOPS Pages: 18

Brand: TC Electronic Pages: 14

Brand: Access Pages: 7

Brand: VDO Pages: 15

Brand: VDO Pages: 20

Brand: Vari Lite Pages: 14

Brand: Vaniman Pages: 3

MCX-C15 - MusicCAST Network Audio Player

Brand: Yamaha Pages: 65

Brand: Yamaha Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands