komodo KH-283 Building Instruction Manual Download Page 12 | Manualshive

Page: 12 / 12

komodo KH-283 Building Instruction Manual Download Page 12

Komodo Hobby

www.komodohobby.com

11

Warning!!!

The Propeller Saver uses only one O-ring to hold a propeller. As long as the motor
starts to run, the propeller has possibility to fly out from the Propeller Saver Hub. It
can cause all bodily harm, property damage, kits loss and death results. User must
wear protective goggle and protective mask and protective cloth and make sure
nobody close to the propeller before run the motor.

By using or installing the propeller saver in any, you agree to and understand the high
risk of using propeller saver. It is your own decision to use the propeller saver or not.
Komodo Hobby (Trading) Company has no control over of it, no liability may be
assumed, nor will any liability be accepted for crash damage, property damage, kits
loss, all bodily harm and death resulting from the use of the propeller saver.

Congratulation!

You finished the assemble work of your unique outrunner motor project. For more
other selections of outrunner motor kit, please visit the site at

www.komodohobby.com

Should you have any comments of this outrunner motor kit, please feel free to contact
us at

[email protected]

«
...
10
11
12

Summary of Contents for KH-283













Reviews:

No comments