manualshive.com logo in svg

Komatsu 114E-3 Series, Shop Manual, Page: 224 / 342

Share
Download
Komatsu 114E-3 Series Shop Manual Download Page 224

SEN00460-01

40 Troubleshooting

24

114E-3 Series

E-39 Code [451/CA451] Rail Press. Sensor High Error

1

Error code

Failure code

Trouble Abnormally high level in common rail pressure sensor

451

CA451

Contents of 

trouble

• High voltage occurred in common rail pressure sensor.

Action of con-

troller

• Limits output and continues operation.

Problem that 

appears on 

machine

• Engine speed or output drops.
• Engine does not start

Related infor-

mation

• Method of reproducing failure code: Starting switch ON.

Possible causes 

and standard 

value in normal 

state

Causes

Standard value in normal state/Remarks on troubleshooting

1

Defective sensor power sup-
ply 2 system

If failure code [

CA227

] is indicated simultaneously, carry out trouble-

shooting for it first.

2

Defective common rail pres-
sure sensor

a

Prepare with starting switch OFF, then turn starting switch ON
and carry out troubleshooting.

FUEL RAIL PRESS

Voltage

Between (3) – (1)

Power supply

4.75 – 5.25 V

Voltage is measured with wiring harness connected. Accordingly, if 
voltage is abnormal, check wiring harness and controller, too, for 
another cause of trouble, and then judge.

3

Hot short (Short circuit with 5 
V, 24 V circuit) in wiring har-
ness

a

Prepare with starting switch OFF, then turn starting switch ON
and carry out troubleshooting.

Wiring harness between J1 (female) (25) – 
FUEL RAIL PRESS (female) (2)

Voltage

Max. 1 V

4

Short circuit in wiring har-
ness (With another wiring 
harness)

a

Troubleshoot with starting switch OFF, then carry out trouble-
shooting without turning starting switch ON.

Wiring harness between J1 (female) (25) – 
FUEL RAIL PRESS (female) (2) and J1 
(female) (37) – FUEL RAIL PRESS (female) 
(3)

Resis-

tance

Min. 

100 k

z

5

Defective wiring harness 
connector

Connecting parts among common rail pressure sensor, engine wir-
ing harness, and engine controller are suspected. Inspect them 
directly.
• Loose connector, broken lock, broken seal
• Corrosive, bent, broken, forced-in, or extended pin
• Humidity in connector, entry of dirt or dust, poor insulation

6 Defective engine controller

a

Prepare with starting switch OFF, then turn starting switch ON
and carry out troubleshooting.

J1

Voltage

Between (37) – (47)

Power supply

4.75 – 5.25 V

Summary of Contents for 114E-3 Series























































































































































































































































































































































Reviews:

No comments