manualshive.com logo in svg

Kollmorgen AKD series, Installation Manual

The Kollmorgen AKD series provides advanced motor drive solutions for various industries. Enhance your knowledge and maximize system performance with the comprehensive Training Manual, available for free download on our website. Unlock the potential of your AKD series products and optimize operations today! [Website]

Share
Download
background image

9.2 Guide to electrical installation

Install the drive electrical system as follows:

1. Select cables in accordance with IEC 60204 (

➜

# 42).

2. Install shielding and ground the drive.

For EMC-compliant shielding and grounding,see (

➜

# 99)(

➜

# 84) ff.

Ground the mounting plate, motor housing and CNC-GND of the control system.

3. Wire the drive and connectors.

Observe the "Recommendations for EMI noise reduction": (

➜

# 99)

Wire the FAULT contact in series into the emergency off circuit of the system.
Connect the digital control inputs and outputs.
Connect up analog ground (also if fieldbuses are used).
Connect the analog input source, if required.
Connect the feedback device.
Connect the hardware option.
Connect the motor cable
Connect shielding at both ends. Use a motor choke if cable > 25m.
Connect motor-holding brake, connect shielding at both ends.
If required, connect the external regen resistor (with fusing).
Connect the auxiliary supply (maximum permissible voltage values see electrical data
(

➜

# 37) or (

➜

# 38).

Connect the mains filter with AKD-xzzz06 (shielded lines between filter and drive).
Connect the main electrical supply.
Check maximum permitted voltage value (

➜

# 37) or (

➜

# 38).

Check proper use of residual-current circuit breakers (RCD): (

➜

# 66)

Connect the PC (

➜

# 171) for setting up the drive.

4. Check the wiring against the wiring diagrams.

AKD Installation | 9   Electrical Installation

Kollmorgen | kdn.kollmorgen.com | October 2017

79

Summary of Contents for AKD series

























































































































































































































Reviews:

No comments

Related manuals for AKD series

Fender 65 Princeton Reverb Service Diagram preview
65 Princeton Reverb
Brand: Fender Pages: 2
NAD PP 375 Mounting Instruction preview
PP 375
Brand: NAD Pages: 2
NAD Masters M3 Specification Sheet preview
Masters M3
Brand: NAD Pages: 4
Nady Audio XA Owner'S Manual preview
XA
Brand: Nady Audio Pages: 12
NAD C375BEE Datasheet preview
C375BEE
Brand: NAD Pages: 4
NAD M10 V2 Quick Start Manual preview
M10 V2
Brand: NAD Pages: 2
NAD M10 V2 Owner'S Manual preview
M10 V2
Brand: NAD Pages: 16
NAD CI 8-120 DSP Quick Setup Manual preview
CI 8-120 DSP
Brand: NAD Pages: 2
TC Electronic RH450 User Manual preview
RH450
Brand: TC Electronic Pages: 22
Fender Acoustasonic Junior DSP User Manual preview
Acoustasonic Junior DSP
Brand: Fender Pages: 20
VINCENT SP-331 Instructions For Use Manual preview
SP-331
Brand: VINCENT Pages: 48
Altec Lansing 9440A POWER AMPLIFIER Specifications preview
9440A POWER AMPLIFIER
Brand: Altec Lansing Pages: 4
Crown DCi 2 1250N Operation Manual preview
DCi 2 1250N
Brand: Crown Pages: 72
Thinuna TA-120D II Operation Manual preview
TA-120D II
Brand: Thinuna Pages: 12
Fenton AV150BT Instruction Manual preview
AV150BT
Brand: Fenton Pages: 7
Kustom KMA16/16R Owner'S Manual preview
KMA16/16R
Brand: Kustom Pages: 4
Lindsay LHA Series Instruction Manual preview
LHA Series
Brand: Lindsay Pages: 3
Pyle Pro PPG860A Owner'S Manual preview
PPG860A
Brand: Pyle Pro Pages: 2

Brands by name

Popular brands

Load more brands