Kollmorgen AKD series Installation Manual Download Page 172 | Manualshive

Page: 172 / 216

background image

AKD Installation | 9 Electrical Installation

9.19.4 Setting the IP Address AKD-B, AKD-P, AKD-T

The IP address can be flashed across the LED display if the B1 button is pressed.

You can use the rotary switches to set the IP address of the AKD. For CANopen and some
other fieldbuses, the rotary switches also set the node address of the drive for that specific
network.

Rotary Switch Setting Drive IP Address

00

DHCP/AutoIP address. The IP address of the drive is obtained
from the DHCP server on your network. If no DHCP server is
found the IP addresses is an AutoIP address (it is internally gen-
erated following the AutoIP protocol and will be of the form
169.254.xx.xx).

01 to 99

Static IP Address. The IP address is 192.168.0.nn, where nn is the
number from the rotary switch. This setting generates addresses in
a range from 192.168.0.

1

to 192.168.0.

99

. Example:if S1 is set to 2

and S2 is set to 5 – the IP address is 192.168.0.25

The PC subnet mask must be set to 255.255.255.0 or 255.255.255.128
When connecting the AKD directly to a PC, use static IP addressing (not 00).

Static IP addressing

When connecting the drive directly to a PC, static IP addressing must be used. Set rotary
switches S1 and S2 to a number different from 00 (see table above).

Dynamic IP addressing (DHCP and Auto-IP)

With S1 and S2 both set to 0, the drive is in DHCP mode. The drive will acquire its IP
address from an external DHCP server if present in the network. If a DHCP server is not
present, the drive will assume an Automatic Private IP Address of the form 169.254.x.x.

If your PC is directly connected to the drive, and set to obtain an IP address automatically in
the TCP/IP settings, a connection will be established with both devices using compatible
automatically generated addresses. It can take up to 60 seconds for a PC to configure an
Automatic Private IP Address (169.254.x.x).

Changing the IP address

If the switches are altered while 24 V Logic power is supplied to the drive, you must switch
off and then switch on again the 24 V supply voltage. This action will reset the address.

172

Kollmorgen | kdn.kollmorgen.com | October 2017

«
...
170
171
172
173
174
...
»

Summary of Contents for AKD series

























































































































































































































Reviews:

No comments

Related manuals for AKD series

Brand: Nakamichi Pages: 34

Brand: Accuphase Pages: 23

Richer Bass RB1

Brand: Laney Pages: 8

Brand: Laney Pages: 16

Brand: Laney Pages: 6

Brand: Accuphase Pages: 33

Reference 750 SE

Brand: Audio Research Pages: 18

Thunder Elite TE601D

Brand: MTX Pages: 1

Brand: Kramer Pages: 13

Brand: Magnat Audio Pages: 7

BLACK CORE FIVE

Brand: Magnat Audio Pages: 57

Brand: unidor TRsystems Pages: 20

Brand: Lab.gruppen Pages: 31

Brand: RVR Solar Pages: 86

Brand: Microlynx Systems Pages: 8

Brand: DOD Pages: 4

Brand: VOX Amplification Pages: 69

Brand: Audio Note Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands