Kollmorgen AKD series Installation Manual Download Page 170 | Manualshive

Page: 170 / 216

background image

AKD Installation | 9 Electrical Installation

9.18.2 SD Card Slot with AKD-M

AKD PDMM offers a SD card slot and push-buttons B2 and B3 to activate file transfers
from/to the AKD PDMM and SD Memory Card. These features can be started from the KAS
IDE software as well. Detailled description can be found in the KAS IDE Online Help.

The backup/restore operations (AKD PDMM to SD or SD to AKD PDMM) will not be possible
if an application is running.

Stop the application from the web-browser or use the B2/B3 “stop” action before initiating
any SD card functionality.
If a fault occurs during save/load operations, the fault number is displayed in the one digit dis-
play with E followed by two digits. Error codes (

Supported SD card types

SD cards are preformatted by the manufacturer. The following table outlines the SD card
types and AKD PDMM support.

SD Type

File System

Capacity

Supported

SD (SDSC)

FAT16

1MB to 2GB

YES

SDHC

FAT32

4GB to 32GB

YES

SDXC

exFAT (Microsoft)

>32GB to 2TB

NO

Features

If an SD card is plugged into the SD slot and no application programm is running, the push-
button menu (started with B3, (

# 167) shows the possible data transfer functions:

'backup' to copy firmware, configurations, user application, and user data files from the
AKD PDMM to SD card.
'restore' to load firmware, configuration, user application, and user data files from SD card
to AKD PDMM.

170

Kollmorgen | kdn.kollmorgen.com | October 2017

«
...
168
169
170
171
172
...
»

Summary of Contents for AKD series

























































































































































































































Reviews:

No comments

Related manuals for AKD series

Brand: QSC Pages: 26

The Prelude PC-200

Brand: Harman Kardon Pages: 6

Brand: Harman Kardon Pages: 16

Brand: Harman Kardon Pages: 32

Brand: Harman Kardon Pages: 8

Brand: Harman Kardon Pages: 26

Brand: Harman Kardon Pages: 11

Brand: Harman Kardon Pages: 31

Brand: Harman Kardon Pages: 18

Brand: Harman Kardon Pages: 29

Brand: Harman Kardon Pages: 48

Brand: T-audio Pages: 13

SHUTTLE MAX 12.0

Brand: Genz Benz Pages: 9

Brand: Teac Pages: 60

Brand: Pyle Pages: 8

Brand: Fender Pages: 9

Brand: GLEMM Pages: 12

Brand: IC Audio Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands