Kollmorgen AKD series Installation Manual Download Page 167

Page: 167 / 216

9.17 Push-buttons (B1, B2, B3)

The push-buttons can be used to start predefined functions.

9.17.1 Push-button B1 with AKD-B, -P, -T

Function

Push-

button

Remarks

Display IP address

Press short to display the IP address in the two digit display

Switches Drive Type
of AKD-x***CC
model

Set rotary switches S1 to 8 and S2 to 9. Press B1 for 3 sec
to switch over from CAN to EtherCAT or reverse.

Load data from SD
card

Drives with I/O option card only.
Set rotary switches S1 to 1 and S2 to 0. Press B1 for 5s for
loading data from the SD card to the drive.

Save data to SD card

Drives with I/O option card only. Set rotary switches S1 to 1
and S2 to 1. Press B1 for 5s for save data from the drive to
the SD card.

AKD Installation | 9 Electrical Installation

Kollmorgen | kdn.kollmorgen.com | October 2017

167

Summary of Contents for AKD series

























































































































































































































Search results

Summary of Contents for AKD series

Reviews:

Related manuals for AKD series

Brands by name

Popular brands

Kollmorgen AKD series, Installation Manual

Search results

Summary of Contents for AKD series

Reviews:

Related manuals for AKD series

Brands by name

Popular brands