Kollmorgen AKD series Installation Manual Download Page 168

Page: 168 / 216

AKD Installation | 9 Electrical Installation

9.17.2 Push-buttons B1, B2, B3 with AKD-M

Function

Push-button Remarks

Unused

Boot-time functions (press and hold button during power-on boot sequence)

Recovery
Mode

Press and hold to boot into recovery mode.

Press and hold to block the application auto-start and to start
cycling through the menu items.

Operational functions (press button during normal operation mode)

Press to cycle through the menu items. The menu items will dis-
played on the 7-segment LED repeatedly for 10 s and can be
selected py pressing B2.

Select Menu
Item

Press while the required menu item is displayed to perform
action.

Application is running

, available menu items:

'IP' address
'stop' application (confirm)

No application is running

, available menu items:

'IP' address
'start' application (confirm)
'reset' to defaults (confirm)
'backup' to SD card (confirm) (

➜

# 170)

'restore' from SD card (confirm) (

➜

# 170)

Confirm

If the selected menu item selection requires a confirmation, "y"
is displayed for 10 s - press B2 to confirm.

168

Kollmorgen | kdn.kollmorgen.com | October 2017

Summary of Contents for AKD series

























































































































































































































Search results

Summary of Contents for AKD series

Reviews:

Related manuals for AKD series

Brands by name

Popular brands

Kollmorgen AKD series, Installation Manual

Search results

Summary of Contents for AKD series

Reviews:

Related manuals for AKD series

Brands by name

Popular brands