Kolin KLG-IF40-2C1M User Manual Download Page 33

Page: 33 / 36

Poor cooling effect.

①

. The air filter is dirty or blocked.

②

. There is heat source or too many people inside the room.

③

. The door or window is open.

④

. There is obstacle at the air intake or outlet.

⑤

. The set temperature is too high.

⑥

. There is refrigerant leakage.

⑦

. The performance of room temperature sensor becomes worse

Poor heating effect

①

. The air filter is dirty or blocked.

②

. The door or window is not firmly closed.

③

. The set room temperature is too low.

④

. There is refrigerant leakage.

⑤

. The outdoor ambient temperature is lower than -5°C.

⑥

. Control loop is abnormal.

Wireless remote

control is not

available

①

. The unit interfered by abnormal or frequent functions switchover

occasionally the controller cannot operate. At this time, you need to pull

out of the plug, and reinsert it.

②

. It is not in its receiving range.

③

. To check the voltage in wireless remote control inside is

charged,otherwise to replace the batteries.

④

. The wireless remote control is damaged.

Water leakage in the

room.

①

. The air humidity is on the high side.

②

. Condensing water over flowed.

③

. The connection position of indoor unit drainage pipe is loosed.

Moisture formed on

air outlet grill

If air conditioner is running in a high humidity for a long time, the moisture may

condense on the air outlet grill and drip off.

Note:

After carrying out the check of the above items and taking relevant measures to

solve the problems found but the air-conditioning unit still does not function well, please

stop the operation of the unit immediately and contact the local service agency

designated by

Kolin

. Only ask professional serviceman to check and repair the unit.

Summary of Contents for KLG-IF40-2C1M





































Search results

Summary of Contents for KLG-IF40-2C1M

Reviews:

Related manuals for KLG-IF40-2C1M

Brands by name

Popular brands

Kolin KLG-IF40-2C1M, User Manual

Search results

Summary of Contents for KLG-IF40-2C1M

Reviews:

Related manuals for KLG-IF40-2C1M

Brands by name

Popular brands