Koldfront TWR327ESS Service Manual Download Page 3

Electrical Safety 

  Do not exceed the power outlet ratings.  

  It is recommended that the unit be connected to its own circuit.  

  A standard electrical supply (120V, 60Hz), that is properly grounded in accordance with the National 

Electrical Code and all state and local codes and ordinances is required.   

  Do not use outlets that can be turned off by a switch or pull chain. 

  Always turn the unit off and unplug it from the outlet when cleaning. 

  Unplug the unit if it is not going to be used for an extended period of time.  

  Do not operate the unit with a power plug missing the ground plug, a damaged cord, or a loose socket. 

  Be sure the appliance is properly grounded. 

  Do not bypass, cut, or remove the grounding plug.  

  If the power cord is damaged, it must be replaced by the manufacturer or a qualified technician.  

  Do not use extension cords or power strips with this unit. You may need to contact an electrician if it is 

necessary to use a longer cord or if you do not have a properly grounded outlet. Do not modify the 
power cord’s length or share the outlet with other appliances.  

 

Do not start or stop the unit by switching the electrical circuit’s power on and off. 

  Immediately unplug the unit if it makes strange sounds, emits an odor or smoke and contact customer 

service. 

  Do not remove any part of the casing unless instructed by an authorized technician. 

  Before the appliance is removed from service or discarded, remove the door and cut off the power 

cord.

 

 

Summary of Contents for TWR327ESS






















Reviews: