1167539-2A-B
2
1167539-2A-B
3
INSTALLATION
How to Install The Side Bodies And The Handles
Remove the nut(9) from each side body (8). Put the o-rings(10) into
groove on the bottom of escutcheons(11). Insert side bodies through
mounting holes from bottom of the lavatory (
NOTE:
The valve body
with red dot should be installed on the left when facing the front of the
faucet, and the valves are in the closed position before installing
them. ).
Install the escutcheon onto each side body. Tighten the nut(9) onto
each side body to secure the escutcheon. Loosen the screws(14) in
the handles(13) with the hex wrench(12), then press the handles onto
the extension stems
(
NOTE:
The handle with red mark should be
installed on the left when facing the front of the faucet, and the valves
are in the closed position before installing them. ). Tighten the screws
(14) to secure the handles with the hex wrench. Wrench tighten the
nuts(16).
Attach the hoses to the side bodies. When facing the front of the
faucet, the left hose connects to the left side body, the right hose
connects to the right side body.
33
31
30
27
28
29
Remove the retaining nut(27). Fit the plastic washer(28) and retaining
nut onto the ball lever(29). Insert the ball lever assembly into the drain
lever hole and through the stopper hole. Tighten the retaining nut.
Be sure that the ball lever rod points to the back of the bidet, tighten
the locknut on the drain body. Remove any excess putty.
NOTE:
Do not reposition the drain after the locknut is tightened, or
you may break the putty seal.
Connect the link(31) onto ball lever rod with "V"-clip(30). Insert the lift
rod(32) into the link of the drain through the hole on the rear of the
spout. Position the lift rod, ensure the distance between the lift rod
knob and the body is about 72mm.
Push the ball lever rod down to the open position. Tighten thumb
screw(33).
26
21
25
23
18
22
24
17
18
19
20
32
How To Install The Spout
Screw the stud(1) to the thread hole on the bottom of faucet. Insert
the lift rod(2) into the hole at the rear of the body assembly. Put the
washer(3) into groove on the bottom of escutcheon(5) through the
flexible hoses(4) and the stud. Insert hoses and stud into the central
hole of lavatory. Position the faucet. From underside of the lavatory, fit
the brackets (6)(Rubber washer is on the top) onto the stud. Secure
the faucet by tightening nuts(7).
3
1
2
5
6
7
4
34
Ensure that all connections are tightened and the handle is in the off
position.
Open the drain. Turn on main water supply and check for leaks.
Repair as required.
Remove the aerator(35) with the key(34). Turn the faucet handle on.
Run hot and cold water through the spout for about one minute to
remove any debris. Remove debris from the aerator. Shut off the
faucet and reinstall the aerator.
35
How to Install The Drain
Take off the stopper(17), drain flange (18) and washer(19) from drain
body(20). Slide washer onto the underside of the drain flange. Take
off the tailpiece(21) from the drain body. Supply enough tape or
sealant to tailpiece thread. Reinstall the tailpiece. With the gasket(22),
steel washer(23) and locknut(24) on the drain body, insert it into the
bidet from underside with the drain lever hole(25) facing the rear.
NOTE:
If needed apply a ring of plumbers putty around the underside
of the drain flange(18), instead of using washer(19).
Thread the drain flange onto the drain body. Tighten the locknut by
hand from the underside. Place stopper into drain body aligning the
flat side of stopper hole(26) with the drain lever hole.
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean
soft cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could
adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
9
11
15
12
13
14
16
8
10
