1049310-2A-A
2
1049310-2A-A
3
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
1
2
3
4
5
6
7
How to Install the Spout
Remove and retain the parts from the spout kit(1) according to the follow-
ing order: nut(3) and metal washer(2).
Install the O-ring(7) to the bottom of the spout through the shank.
Fit the spout to the center hole of lavatory. Install the metal washer and
nut. Adjust the position of the spout and securely tighten nut.
Thread the supply tee(6) with plastic gasket(5) and rubber washer(4) to
the spout shank, tighten by hand.
How to Install the Valve Bodies, the Handles
and the Hoses
Remove the handle kit(8) from the side body(9). Install the sticker
washer(10) into the groove on the bottom of the escutcheon(13).
Put the washers into the ends of the hose(14). Connect the side bodies
and supply tee(6) with hoses as shown in the figure.
NOTE:
The hoses(14) should only be used here.
Insert the side body with dished washer (17), washer(11)and nut(12)
through mounting holes from bottom of the lavatory(For 14406T-4 and
14408T-4, the side body with red mark on the left when facing the front of
the faucet). Press the spline adapter(15) onto the valve stem(16).
Reinstall and tighten the handle kit(The handle with the red washer on
the left when facing the front of the faucet). Tighten the nut(12).
The configuration shown is the correct position of the handles in the
closed position.
8
9
14
11
12 17
14
9
6
13
10
15
16
34
Ensure that all connections are tight. Remove the aerator(34).
Open the drain. Turn on the main supply and check for leaks. Open both
hot and cold valves and run water through the spout to remove any
debris. Turn the valve off. Reinstall the aerator.
How to Install the Drain
Remove the stopper(18), flange(20) and washer(21) from the drain
body(23). Take off the tailpiece(25). Apply thread tape to the tailpiece
and install the tailpiece to drain body. Insert the drain body kit into the
lavatory from underside, and make sure the drain lever hole(22) facing to
the back of the lavatory. Screw the flange with washer into the drain
body. Tighten the locknut(24) by hand from underside of the lavatory.
NOTE:
If needed, apply a ring of plumbers putty around the underside of
the drain flange(20), instead of using washer(21).
Place the stopper(18) into the drain body aligning the flat side of stopper
hole(19) with the drain lever hole.
Remove the retaining nut(29). Fit the plastic washer(27) and retaining nut
onto the ball lever(28). Insert the ball lever assembly into the drain lever
hole and through the stopper hole. Tighten the retaining nut.
Be sure that the ball lever(28) points to the back of the lavatory, tighten
the locknut(24) on the drain body by wrench.
NOTE:
Do not reposition the drain if plumbers putty applied after the
locknut is tightened, or you may break the putty seal. Wipe away excess
plumbers putty.
Insert lift rod(30) to the hole at the rear of the body(33). Assemble the
thumb screw(31) to the link(32), and link onto the ball lever(28) with
“V”-clip (26). Slide the lift rod(30) into the hole in link. Push the ball lever
down into the open position, and adjust the lift rod. Tighten the thumb
screw(31).
20
21
24
18
19
21
25
22
20
23
24
29
27
26
28
28
32
26
31
30
30
33
10
mm
