1115111
-2-G
2
安装步骤
INSTALLATION
How to Install the Faucet
To perform installation, installer must
provide G1/2
˝
female supply fittings,
spaced 150mm apart, horizontally,
vertical, and not more than 5mm if
extending or below the finished wall
surface. Hot supply pipe must be
located on the left.
Install the two offset connectors(1) into
the hot and cold supply fittings. Use
appropriate thread sealants or thread
tape onto the threads.
Adjust the center-to-center distance
between the connectors to 150mm and
horizontally. They should extend 40 to
47mm beyond the finished wall. Apply
a ring of plumbers putty around the
back edge of the escutcheon(2). Keep
the hole facing downward, slide the
escutcheons onto the connectors until
they are against the finished wall. Fix
the escutcheons by tightening the
screws(3). Remove any excess putty.
Put the washers(5) into the nuts(4) and
tighten the nuts with strap wrench.
Put the check valve(6) into the
handspray(7) inlet. Put the restrictor(8)
into the handspray inlet if needed.
Note:
Keep
the O-ring of the check
valve outward.
Connect the shower outlet(10) and
handspray with hose(9).
如何安装水龙头
为使安装顺利，
G1/2
˝
内螺纹管道配件
应已安装好。预留
150mm
的间距，保
持水平，并垂直墙面，低于和高于墙
面的长度不超过
5mm
。热供水管装在
左边。
在两个接头
(1)
涂上螺纹密封胶或缠绕
足以密封的密封胶带，旋入冷热水管
中。
调 节 两 个 接 头 ， 使 其 中 心 距 离 为
150mm
，并保持同一水平。它们凸出
墙面的尺寸应该在
40
到
47mm
之间。在
装饰罩背面边缘涂一圈油灰，保持螺
孔向下，将装饰罩
(2)
套入接头，紧贴
墙壁。锁紧螺钉
(3)
固定装饰罩。去除
多余油灰。
将垫片
(5)
放入水龙头螺母
(4)
中，将螺
母旋到接头上。并用带状扳手拧紧。
将 单 向 阀
(6)
按 图 示 方 向 装 入 手 持 花
洒
(7)
。如需要，将限流器
(8)
塞入手持
花洒进水口。
注意：单向阀带
O
型圈一端必须朝外
(如图所示方向)。
用软管
(9)
连接出水口
(10)
和手持花洒
1
150mm
3
热
HOT
17
冷
COLD
1115111
-2-G
3
12
40.6
2
5
40~47mm
4
How to Install the Bracket
Determine a suitable location on the
finished wall to install the bracket.
Mark bracket support(13) mounting
hole locations on the wall according to
the dimension. Drill two holes on the
finished wall, the holes should match
the anchors(12). Install the anchors.
Tighten screws(14) to secure bracket
support. Apply a ring of plumbers putty
or sealant around the back surface of
the bracket(15). Keep the mounting
hole facing downwards, install the
bracket onto the bracket support.
Secure the bracket by tightening the
screw(16) with hex wrench(11).
Remove any excess puttty or sealant.
如何安装托架
在墙面选一合适的位置来安装托架。
根据安装尺寸在墙壁上标出底座
(13)
安
装孔位。根据胀塞
(12)
的直径打孔，安
装胀塞。旋紧螺钉
(14)
，固定底座。在
托架
(15)
底面边缘涂上一圈油灰或密封
胶，并保持螺孔向下将托架装在底座
上。用六角扳手
(11)
锁紧螺钉
(16)
固定
托架。去除多余油灰或密封胶。
安装结果检查
INSTALLATION CHECKOUT
检查并确保所有的衔接处都已拧紧。
确保手柄在关闭位置。
打开排水系统和主要供水源，检查并
修理有漏水的接口。
浴缸花洒龙头：
取下花洒和起泡器
(17)
。打开冷热水，
让水流出约一分钟以清除杂质。检查
渗漏，清洗起泡器。关闭水龙头，并
装回起泡器和花洒。
花洒龙头：
取下花洒。打开冷热水，让水流出约
一分钟以清除杂质。检查渗漏。关闭
水龙头，并装回花洒。
Ensure that all coupling nuts are
tighten.
Ensure that the handles are in the off
position.
Turn on the main water supply, and
check for leaks. Repair as needed.
Bath & Shower Faucet:
Remove the handspray and aerator
(17). Run hot and cold water through
the faucet for about one minute to
remove any debris. Check for leaks.
Remove any debris from the aerator.
Shut off the faucet. Reinstall the aerator
and handspray.
Shower Faucet:
Remove the handspray. Run hot and
cold water through the faucet for about
one minute to remove any debris.
Check for leaks. Shut off the faucet.
Reinstall the handspray.
9
10
13
14
16
11
15
▲
▲
清理说明
CLEANING INSTRUCTIONS
适用于所有加工处理过的表面：以中性肥皂水清洗
镀层表面，再以干净的软布彻底擦干整个表面，许
多清洁剂，比如氨水、去污粉及洁厕灵等，会对电
镀表面造成伤害，切忌使用。
有磨损性的清洁用具或清洁剂也不可使用于科勒牌
的水龙头及其配件上。
All Finishes: Clean the finish with mild soap and warm
water. Wipe entire surface completely dry with clean
soft cloth. Many cleaners may contain chemicals, such
as ammonia, chlorine, toilet cleaner etc. which could
adversely affect the finish and are not recommended
for cleaning.
Do not use abrasive cleaners or solvents on Kohler
faucets and fittings.
7
7
6
8
。
