background image

   

                                                                          

1206124-2A-C            

                                                                                                                                        2   

  

   

                                                                          

1206124-2A-C            

                                                                                                                                        3  

  

INSTALLATION CHECKOUT

CLEANING INSTRUCTIONS

All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft 

cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely 

affect the finish and are not recommended for cleaning.

Do not use abrasive cleaners or solvents on Kohler faucets and fittings. 

INSTALLATION

How to Install the Spout

Remove the center tee(9), the nut(6) and the washer(5) from the 

shank(2). Leave the rubber washer(7) and the plastic gasket(8) in the 

center tee.

Slide the escutcheon(3) onto the bottom of the spout kit(1) through the 

shank. Slide the rubber washer(4) into the bottom groove of the 

escutcheon. Insert the lift rod(10) to the back hole on the faucet. Then fit 

the spout kit into the center hole of lavatory. From underside of the 

lavatory, install the washer(5) and the nut(6). Position the spout. Secure 

the spout kit by tightening nut. Reinstall the center tee.

How to Install the Valve Bodies and Handles

Put the nut(21) and metal washer(20) onto each side body(22). Insert 

side bodies through mounting holes from bottom of the lavatory(

NOTE:

 

The valve body with red dot should be installed on the left, and the valves 

are in the closed position before installing them).

Install the rubber washer(17) and the escutcheon(16) onto each side 

body. Press the spline adapter(18) onto each valve stem(19), then press 

the handle(15) onto each spline adapter. Secure the handles by the 

screws(13) with the washers(14). Press the plug(12) into the hole on the 

top of each handle, the plug with ‘H’ mark is on the left. Wrench tighten 

the nuts(21). 

One end of the hose(23) connect to the outlet of side body, and the other 

end connect to the center tee(9).

Ensure that all coupling nuts are tight. Ensure that the lever handles are 

in the off position. Turn on the main water supply and drain, and check for 

leaks. Repair as needed.

Remove the aerator(38) by key(39). Run hot and cold water through 

faucet for about one minute to remove any debris. Check for leaks. 

Repair as needed. Remove any debris from the aerator. Shut off the 

faucet. Reinstall the aerator.

NOTE: 

If needed, apply a ring of plumbers putty around the underside of 

the drain flange(26), instead of using washer(27).

Place stopper(24) into drain body aligning the flat side of stopper hole(25) 

with the drain lever hole.

Remove the retaining nut(33). Fit the plastic washer(34) and retaining nut 

onto the ball lever(35). Insert the ball lever assembly into the drain lever 

hole and through the stopper hole. Tighten the retaining nut.

Be sure that the ball lever(35) points to the back of  the lavatory, tighten 

the locknut(30) on the drain body by wrench. 

NOTE:

 Do not reposition the drain if plumbers putty applied after the 

locknut is tightened, or you may break the putty seal. Wipe away excess 

plumbers putty.

Assemble thumb screw(36) to link(37), and link onto ball lever rod(35) 

with ‘V’-clip(32). Slide lift rod(10) into the hole in link. Push the ball lever 

down into the open position, and adjust the lift rod. Tighten thumb 

screw(36).

How to Install the Drain

Remove stopper(24), flange(26) and washer(27) from drain body(29). 

Take off the tailpiece(31). Apply thread tape to tailpiece and install the 

tailpiece to drain body. Insert drain body kit into the  lavatory from 

underside, and make sure the drain lever hole(28) facing to the back of 

the lavatory. Screw the flange with washer into the drain body. Tighten 

the locknut(30) by hand from the underside of the fixture.

1
2

3

7

8
9

9

10

4

16

15

14

13

12

17
18

19
20
21

22

23

5
6

26

27

30

24

25

27

31

28

26

29

39

38

30

33

34

32

35

35

37

32

36

10

Reviews: