1330478-T01-A
-2-
3. Insert the floor drain body outlet back into the waste
pipe.
将地漏本体排水口套回地面排水管内。
4. If there is no leakage, finish the following layer in proper
order: mortar, primer coat, water-proof sealant, cement
and tiles. The finished floor shall have a 2% slope.
Place the inner core of the floor drain into its main body
and press it tightly.
经测试无渗漏后，依次完成砂浆层，底漆层，防水层，水
泥层和瓷砖层。完成后的瓷砖面应向地漏有
2%
的斜度。
将地漏内芯放入地漏本体，压紧。
2% Slope
2%
斜度
CARE AND CLEANING
CARE AND CLEANING
护理和清洁
为了长久使用，请在护理您的科勒产品时注意以下几点：
使用中性清洁剂，例如液体洗洁精和温水进行清洗。
请不要使用研磨清洁剂，以免刮划或使表面变钝。
请仔细阅读清洁剂说明以确认其能够在产品上安全
使用。
在大面积使用清洁剂之前，请务必先在不显眼处先试
验清洁方式。
请不要将产品表面浸泡在清洁剂中。
使用清洁剂后，请立即擦拭并用水彻底清洗。清洗并
擦干溢溅在周围表面的清洁剂。
使用柔软湿润的海绵或清洁布，请勿使用研磨材质，
例如刷子和百洁布来清洁表面。
使用过程中如需清理地漏内芯，请将内芯直接提出，
装回内芯时，请直接放入压紧。
For best results, keep the following in mind when caring
for your KOHLER product:
Use a mild detergent such as liquid dishwashing soap
and warm water for cleaning. Do not use abrasive
cleaners that may scratch or dull the surface.
Carefully read the cleaner product label to ensure
the cleaner is safe for use on the material.
Always test your cleaning solution on an inconspicuous
area before applying to the entire surface.
Do not allow cleaners to sit or soak on the surface.
Wipe surfaces clean and rinse completely with water
immediately after cleaner application. Rinse and dry
any overspray that lands on nearby surfaces.
Use a soft, dampened sponge or cloth. Never use
an abrasive material such as a brush or scouring
pad to clean surfaces.
When it is necessary to clear the inner core of the floor
drain during use, please lift it out directly. When installing
it, please place it into it directly and press it tightly.
K-26228T Instructions for installation of the floor drain and washing machine drain pipe
K-26228T
地漏与洗衣机排水管安装说明
Installation steps:
1. Assemble the plastic sleeve onto the plastic restrictor
(please determine whether a plastic sleeve is needed
or not according to the size of the washing machine
drain pipe);
2. Assemble the washing machine drain pipe onto the plastic
sleeve or plastic restrictor; Make sure there is no leakage
after checking against STEP 5, and fix it with a band;
3. Screw and tighten the assembled parts into the
two-way bend;
4. Slide the floor drain cover plate onto the two-way bend,
and then tighten with a plastic nut; finally, install onto
the floor drain body.
5. Check for water leakage when the washing machine
drains water, if yes, please bind the PTFE tape at the
corresponding position of the rubber sleeve or the
restrictor, re-confirm water leakage.
安装步骤：
1.
将橡胶圈插入塑料限流管上（请根据洗衣机排水管规格
选择是否需要橡胶圈）；
2.
将洗衣机排水管插入橡胶圈或塑料限流管上；经步骤
5
检
验，确认不漏水后，用扎带固定；
3.
将组装好的组件旋入两通弯头螺纹上，并旋紧；
4.
将地漏盖板套入，并用塑料螺母旋紧，最后装入地漏本
体上。
5.
检查洗衣机排水时是否漏水，如有漏水，请在橡胶圈或
限流管上对应位置缠上生料带，并再次确认是否漏水。
List Of Parts
零件清单
Washing Machine
Drain Pipe
洗衣机排水管
Rubber Sleeve
橡胶圈
Plastic
Restrictor
塑料限流管
Two-way
Bend
两通弯头
Floor Drain
Cover Plate
地漏盖板
Plastic Nut
塑料螺母
1
2
3
4
Note:
The yellow flow
restrictor is for drum washing
machine, while the gray flow
restrictor is for impeller
washing machine.
注意：
滚筒洗衣机使用黄色限
流管。波轮洗衣机使用灰色限
流管。
Plastic Tie
扎带
Plastic Tie
扎带
