background image

1106828-2A-AA/Rev04

Install the mounting stud(2) onto the faucet body base(3). Insert lift rod

(5) to the hole of the body. Slide the washer(4) over the flexible hoses(1)

and mounting stud(2), and into the groove at the bottom of the faucet

body.

Insert the flexible supply hoses(1) into the lavatory hole. Position the

faucet. From underside of the lavatory, place the bracket(6)(Rubber

washer is on the top) onto the mounting stud, and secure the faucet with

the nut(7).

Attach the hoses to water supplies. When facing front of faucet , the left

hose connects to hot water, the right hose with "COLD" label connects to

cold water.

Remove flange(8) from drain body. Slide the washer(9) onto the

underside of the drain flange. Apply thread tape to tailpiece (10). Install to

drain body(11). Insert drain body into underside of lavatory with drain

lever hole(12) facing to the back of lavatory and thread flange(8) onto

drain body until hand tight. Tighten the locknut(13) by hand from the

underside of the fixture.

Place stopper (14) into drain body aligning the flat side of stopper hole

(15) with the drain lever hole.

Place the rubber washer(16) into the drain lever hole(12). Put another

plastic washer (17) and retaining nut(18) into the long end of ball lever rod

(19). Insert the ball lever assembly(20) into the drain lever hole and

through the stopper hole(15), and tighten the retaining nut(18).

Be sure that the ball lever points to the back of the lavatory. Tighten the

locknut (13) onto the drain body. Remove any excess putty.

If needed apply a ring of plumbers putty around the underside of

the drain flange(8), instead of using washer(9).

19

18

20

13

16

17

9

8

13

12

10

11

8

14

15

2

3

5

4

1

6

7

Summary of Contents for July 16027

Page 1: ...rves the right to make changes in product characteristics packaging or availability at any time without notice Please leave these instructions for the consumer They contain important information 1 Flush the water supply pipes thoroughly to remove debris 2 For new installations assemble faucet and drain to lavatory before installing lavatory G1 2 30 105 37 31 7 36 5 54 176 5 Drain not for 16027 4ND...

Page 2: ...lpiece 10 Install to drain body 11 Insert drain body into underside of lavatory with drain lever hole 12 facing to the back of lavatory and thread flange 8 onto drain body until hand tight Tighten the locknut 13 by hand from the underside of the fixture Place stopper 14 into drain body aligning the flat side of stopper hole 15 with the drain lever hole Place the rubber washer 16 into the drain lev...

Page 3: ... and check for leaks Repair as required Remove aerator 24 Turn on the faucet Run hot and cold water through spout for about a minute to remove any debris Remove any debris from aerator Shut off the faucet and reinstall aerator All Finishes Clean the finish with a mild soap and warm water Wipe entire surface completely dry with a clean soft cloth Many cleaners may contain chemicals such as ammonia ...

Page 4: ...34799 Aerator O Ring 1080817 834753 Pop Up Drain O ring 880084 O ring 871472 880008 Stopper 880037 Link Kit 880406 Washer Mounting Hardware 836664 837261 for Thailand 834562 Not for 16027 4ND 1068079 for India Not for 16027 4ND Nut 3010213 1031237 for 16027A 4ND Hose 834754 1024405 for India 1054593 for 16027A 4ND 1110391 Lever ...

Reviews: