Kohler CURTIS 3401T Manual Download Page 29 | Manualshive

Page: 29 / 62

background image

3 — INSTALLATION AND WIRING

pg. 23

Curtis Model 3401T – August 2022

I/O CONNECTOR

The mating connector is a 16-pin Mini-Universal MATE-N-LOK housing from TE Connectivity.

The face is sealed to IP65. The rear is sealed to IP65 for electronic components and IP40 for the

connector. Curtis recommends that you increase the connector’s protection to IP54 by using the

parts listed in Table 3-2.
The following tables list the TE Connectivity parts for IP40 and IP54 protection.

Table 3-1 Mating Connector Parts — IP40 Protection

Part

TE Connectivity Part Number

Connector Housing

770583-1

Terminal (18–22 AWG)

770904-

X

Table 3-2 Mating Connector Parts — IP54 Protection

Part

TE Connectivity Part Number

Connector Housing

794824-1

Terminal (18–22 AWG)

770904-X

Interface Seal

1-1586362-6

Single Wire Seal or Gang Seal

• Single: 794758-1
• Gang: 1-1586359-6

Cavity Plug Seal (for unused

terminal positions)

794995-1

«
...
27
28
29
30
31
...
»

Summary of Contents for CURTIS 3401T































































Reviews:

No comments

Related manuals for CURTIS 3401T

Brand: Daewoo Pages: 2

Brand: Taber Pages: 53

Brand: Roland Pages: 15

Brand: IEI Technology Pages: 85

SourceMeter 2400

Brand: Keithley Pages: 594

System SourceMeter 2601B

Brand: Keithley Pages: 864

Brand: Labgear Pages: 8

SourceMeter 2600B Series

Brand: Keithley Pages: 897

Brand: AEMC Pages: 4

Brand: Hanna Instruments Pages: 9

MTEK6000 Series

Brand: Metretek Pages: 81

Brand: Keysight Pages: 92

Brand: OHAUS Pages: 84

Brand: Sonel Pages: 84

Brand: SBS Pages: 17

Brand: Omega Pages: 15

Brand: TASKING Pages: 12

Brand: PCB Piezotronics Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands