background image

13

Figure 15.

Fuel Tank Filter

A serviceable fuel tank filter is located under the fuel

tank cap, in the filler neck.

Daily or as required

 clean filter of any accumulation

as follows:

1. Remove the fuel tank cap and filter.

2. Clean the filter with solvent, replace if damaged.

3. Wipe the filter and insert it.

CAUTION!

Be sure the tank cap is tightened securely.

Figure 16.

Muffler Screen and Spark Arrestor

Engines are equipped with a muffler screen and spark

arrestor for operational and environmental safety. One

of two configurations will be used, determined by the

engine model involved.

Every 

100 hours

 of operation, remove and clean or

replace the muffler screen and/or spark arrestor

following the instructions below.

Muffler Screen CS4,CS6

CAUTION!

The engine and muffler will be very hot after the engine

has been run.

Avoid touching the engine and muffler while they are

still hot, with any part of your body or clothing.

1. Remove the muffler screen.

2. Clean the carbon deposits out of the muffler

screen using a wire brush.

3. Check the muffler screen, replace if damaged.

4. Install the muffler screen.

Figure 17. Muffler Screen.

All manuals and user guides at all-guides.com

Summary of Contents for Command Pro 10





















Reviews: