background image

22

1290447-W2-B

Fault Diagnosis

Symptom

Cause/Action

1.

 Only Hot or Cold Water From 

Outlet

a.

  Inlet  supplied  reversed  (i.e.  hot  supply  to  cold  inlet)  can  be  diagnosed  by 

isolating  the  inlet  supplies  and  removing  the  valve  cartridge.  With  cartridge 

removed, turn the water on at each supply individually and at a very low flow rate 

(water will run out of the front of the valve body). Identify which inlet is the hot 

supply and which is the cold supply. Re-install the cartridge matching the raised 

H and C on the cartridge body to the inlets as identified.

b. 

No hot water reaching mixing valve. Check

c.

 Check strainers and inlet fittings for blockage.

d.

 Refer to symptom 5 below.

e.

 Installation conditions continuously outside operating parameters

f.

  Normal  function  of  mixing  valve:  indicates  hot  water  inlet  supply  failure/

interruption.

2.

  Fluctuating  or  Reduced  Flow 

Rate

Normal function of mixing valve when operating conditions are unsatisfactory.

a.

 Check strainers and inlet/outlet fittings for flow restriction.

b.

 Ensure that minimum flow rate is sufficient for supply conditions.

c.

 Ensure that dynamic inlet pressures are nominally balanced

d. 

Ensure that inlet temperature differentials are sufficient.

e.

  (Subject  to  rectification  of  supply  conditions).  Check  the  thermostatic 

performance; renew cartridge assembly if necessary.

f.

  Normal  function  of  mixing  valve:  indicates  hot  water  inlet  supply  failure/

interruption.

3.

  No  Flow  From  Mixing  Valve 

Outlet 

Check that inlet flow controls are fully open.

a.

 Check strainers and inlet/outlet fittings for blockage.

b.

 Cold supply failure; thermostat holding correct shutdown function: rectify, and 

return to 

2e above

.

4.

 Blend Temperature Drift

Indicates operating conditions changed.

a.

 Refer to symptom 

2 above

.

b.

 Hot supply temperature fluctuation (rectify and refer to Commissioning).

c.

 Supply pressure fluctuation (rectify and refer to Installation).

5.

  Hot  Water  in  Cold  Supply  or 

Vice-Versa

Indicates check valves require maintenance (refer to Maintenance).

6.

 Water Leaking form Valve Body Seal (s) worn or damaged.

a.

 Obtain seal pack, renew all seals.

b.

 (If leak persists from around temperature spindle). Renew cartridge assembly.

7.

 Cold Water does Not Flow After 

Hot Supply Failure

a.

 Incorrect valve model installed. Check and rectify.

b. 

Incorrect internal cartridge installed. Check identification code and rectify

c.

 Check strainers and inlet/outlet fittings for blockage

d. 

Cold supply failure.

8.

  Hot  Water  continues  to  Flow 

After Cold Supply Failure

a. 

Incorrect Valve commissioning. Validate the Commissioning.

b.

 Insufficient temperature differential see validate commissioning.

Summary of Contents for 320 F

























Reviews: