background image

• If you are interrupted when operating the drill, complete the process and switch off before looking up.

• Periodically check that all nuts, bolts and other fixings are properly tightened.
• When using the drill, use safety equipment including safety glasses or shield, ear defenders, and protective

clothing including safety gloves. Wear a dust mask if the drilling operation creates dust.

If in doubt, do not plug in the tool. Using a power source with a voltage less than the nameplate rating is 
harmful to the motor.

The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual will be considered a case of misuse. The user and not the

manufacturer shall be liable for any damage or injury resulting from such cases of misuse.

To use this tool properly, you must observe the safety regulations, the assembly instructions and the operating
instructions to be found in this manual. All persons who use and service the machine have to be acquainted 

with this Manual and must be informed about its potential hazards.

Children and frail people must not use this tool. Children should be supervised at all times if they are in the area 

in which the tool is being used. It is also imperative that you observe the accident prevention regulations in 
force in your area. The same applies for general rules of occupational health and safety.

The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such 
changes. Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors. The 

following hazards may arise in connection with the tool’s construction and design:
• Damage to the lungs if an effective dust mask is not worn.
• Damage to hearing if effective ear defenders are not worn.

Additional safety instructions for the charger

• Your tool with Lithium Ion batteries may only be charged with the specific designed and supplied 
Lithium Ion battery charger purchased with the tool.
IT IS DANGEROUS TO USE ANY OTHER BATTERY CHARGER TO CHARGE YOUR TOOL. 
Do not attempt to charge the battery pack with any other charger than the one supplied.

• If there is a problem with the battery or the tool, contact the Kogan customer support team for assistance in 
rectifying your problem.
• Before using the charger, read all the instructions, labels and cautionary markings on the charger and battery 
pack as well as the instructions on using the battery pack.
• Do not use the charger if it has been subjected to a heavy knock, dropped or otherwise damaged in anyway.
Contact Kogan customer support so they can arrange a check or repair of the unit.
• Do not disassemble the charger. Opening or removing covers may expose you to dangerous voltages or other
risks. Incorrect reassembly can cause electric shock when you use the tool or charger again. Contact the Kogan 
customer support centre when service or repair is required. Incorrect re-assembly may result in the risk
of fire, electric shock or electrocution. To reduce the risk of electric shock, do not disassemble any part of the
product.
• DANGER. If the battery pack is cracked or damaged in any other way, do not insert it in the charger
• Do not plug anything other than your tool into the charger, as other objects may touch dangerous voltage 
points or short out parts, which could result in fire or electric shock.
• Do not place the tool or charger on an uneven surface, as a fall may cause serious damage.
• Never place the tool or charger near or over a heat source such as a radiator or heater.
• Do not operate the charger in a cabinet or other enclosure unless proper ventilation is provided.
• Use the battery charger indoors only.

WARNING. Do not allow any liquid to come into contact with the charger. There is a danger of electric shock. Do 
not position the tool or battery charger near water; for example, near a sink, wash bowl or toilet. Do not spill 
liquid of any kind on the tool or charger. Doing so may short out parts, causing damage to the product and 
creating the risk of fire or electric shock.

Summary of Contents for KADRI20AUTA














Reviews: